Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Discussion Forum
:

Advise on what to do next

Welcome Guest, Log in or Register
Author 
tom rollins 52

12-04-2000 02:39:35




Report to Moderator

I have started tearing down the engine on my 52 8N, got the head off and found the exhaust valves had a build up of white deposits on them and the intake valves were black, can they just be cleaned up and reused? Hardly any deposits on the tops of the pistons. There is a very small ridge on the walls of the cylinders but the rest of the cylinders look good. Could I just get the ridge off and rering the pistons or should I replace the sleeves. Thanks for the adivse

[Log in to Reply]   [No Email]
Dell (WA)

12-04-2000 12:13:58




Report to Moderator
 Re: advise on what to do next in reply to tom rollins 52 8N, 12-04-2000 02:39:35  
Tom..... ...white deposits on the exhaust valves are called "carbon", a natural byproduct of combustion. Eventually, the carbon can become so thick and hot that it causes pre-ignition and subsequent damage to the engine. It usually wirebrushes off with no problems.

Black deposits on intake valves are oil and fuel that would turn into "carbon" except the intake valve never gets hot enuff because it is always getting cool air from the carb. Wire brush 'em clean.

The small ridge on the top of your cylinders is a sign of worn sleeves. REPLACE 'EM. They are designed to be replaced and are not expensive. Your friendly engine machine shop can replace 'em cheeper than they can use a boaring bar to machine off the ridge. By using new sleeves, you know the cylinders will be round and not tapered and you can use standard piston rings.

Do the job right so you can amaize your friends and brag a little..... ....Dell

[Log in to Reply]  [No Email]
Bill In Houston

12-04-2000 10:59:38




Report to Moderator
 Re: advise on what to do next in reply to tom rollins 52 8N, 12-04-2000 02:39:35  
Tom;

I hope you don't feel like we are piling on you. I agree with the rest. Rebuild the engine. Let's say there are six things that need repair. You choose to do two or three or four. In the back of your mind, you are going to wonder hold long before that fifth or sixth "thing" will last.

If you have a ridge on your sleeves, then there is wear on the sleeves, rings, bearings, pistons, etc. You might get buy on the valves, but has long as you have it down, you might as well do it all. If you rebuild the tractor, it will run better. I take that back, it will run great. If you do five of the hypothetical six things, that sixth might be enough to keep it from running well.

I redid my motor this summer. a lot of components looked as if they were new. I replaced them anyway. I even put on a new manifold. I do not think the tractor has ever run as smooth as it does now, not in the 18 years I have owned it.

Ultimately, it is your decision. Good luck.

Regards
Bill

[Log in to Reply]  [No Email]
bg

12-04-2000 06:23:24




Report to Moderator
 Re: advise on what to do next in reply to tom rollins 52 8N, 12-04-2000 02:39:35  
Since you already have it torn down, why not go ahead and do a complete renewal. It may cost a little more now, but at least you will have done all you can do and will have essentially a new motor. If you decide you don't want to do a complete overhaul, you could get the bore mic'ed, then re-ring and have the ridge cut off if needed. I'd still wonder about the bearings. I'd feel better about doing the top and bottom end, 'cause it's not fun to have to tear it down again after a few months.

[Log in to Reply]  [No Email]
???

12-04-2000 05:14:32




Report to Moderator
 Re: advise on what to do next in reply to tom rollins 52 8N, 12-04-2000 02:39:35  
I don't think it's What do I do Next as much as What should I have done First.

1 Why did you decide to take the head off?
2 How was the tractor running Before this? 3 Why didn't you ask questions First?

The White exhaust shows that it's NOT burning Oil.
How did the Plugs look when you took them out?



[Log in to Reply]  [No Email]
TimK

12-04-2000 08:21:50




Report to Moderator
 Re: Re: advise on what to do next in reply to ???, 12-04-2000 05:14:32  
In addition to the other responses, I think part of your decision to re-sleeve should be based on what kind of sleeves you have. Assuming you have .090" sleeves, those require some special tools and a hydraulic press which most of us-uns don't have, which means you have to take the engine to the shop, which means you probably will doing more on the rebuild. The thinner steel sleeves can be installed by you, which means cheaper, maybe faster. I have a problem, personally, when I see people trying to do "part" of a rebuild. Once you start digging into these old engines, generally, you will find other things that are marginal and should be replaced e.g. timing gear, oil pump, rod inserts, etc. etc. I have a problem putting an engine back together knowing that there are these "weak areas" that could give problems anytime in the future, although I have read numerous accounts on this Board where people have done just that. My $ .02.

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy