Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Discussion Forum
:

MF 250

Welcome Guest, Log in or Register
Author 
Leon Miller

03-31-2000 17:30:40




Report to Moderator

Can't shift my PTO in with engine running. Was told to adj clutch and did so. Also told me clutch pedal 3/4 down will let you shift tranny but it has to be all the way down to shift PTO.
Still gears grind when trying to engage PTO w/clutch all the way down. Tractor is 1986 with 900 hrs on it. Everything else perfect. What is the problem. Operator ? Thanks Leon




[Log in to Reply]   [No Email]
Jack in NB

04-01-2000 09:13:04




Report to Moderator
 Re: MF 250 in reply to Leon Miller, 03-31-2000 17:30:40  
Hi Leon -

Normal break point for the PTO clutch to kick in is about half way down.

Is your free play adjusted correctly? Pedal travel should be about 3/8" from the upper stop if it's set properly.

The next adjustment is primary pressure plate travel. This is the 3 cap screws with lock nuts (1/2" heads) around the perimeter of the clutch.

These are accessible through the large hole in the bottom of the bell housing.

Factory spec clearance is about .090; we set them to .060 +/- to ensure complete PTO release at full clutch travel.

Be sure to use a GOOD wrench on the screws and lock nuts. They can be set quite firmly, and it's easy to strip the heads in the cramped location. If you strip them, you have to split the tractor to repair the problem.

Hope this helps; let us know how you make out.

[Log in to Reply]  [No Email]
Jack in NB

04-01-2000 09:16:49




Report to Moderator
 Re: Re: MF 250 in reply to Jack in NB, 04-01-2000 09:13:04  
Addendum: The 3/8 clearance is for the 35. The 250 may have a different pedal configuration - the free play travel at the footplate on the pedal should be 1/2" to 1".



[Log in to Reply]  [No Email]
Leon Miller

04-10-2000 16:19:18




Report to Moderator
 Re: Re: Re: MF 250 in reply to Jack in NB, 04-01-2000 09:16:49  
Jack I finally got the tractor out and got the clutch adjusted. You was right about cramped quarters. I took my torch and bent a wrench to get the proper angle on the lock nut as it was tight. A little penetrating oil also helped.
After the adjustment the PTO shifts fine with the engine running. Thanks for your help....Leon



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy