Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Discussion Forum
:

John Deere ? vs A-C D17 seriesIV

Welcome Guest, Log in or Register
Author 
Kent

09-10-2002 21:03:57




Report to Moderator

What John Deere tractor would you compare to the Allis Chalmers D17 seriesIV from the same era and or equal value. I can't seem to find a D17 and I know JD parts seem to be more plentiful. Any ideas or suggestions. Thanks Kent




[Log in to Reply]   [No Email]
Kent

09-11-2002 19:12:37




Report to Moderator
 Re: John Deere ? vs A-C D17 seriesIV in reply to Kent, 09-10-2002 21:03:57  
Thanks for the quick replys. I may give up my search for a D-17 and look for a 170/175 or a JD 20 series. I kinda need the low style tractor to do trim work and get a loader for it later. I have a gas AC-190 and it is pretty conservative on fuel. Bought it @ 6 months ago for $1600 with tranny problems. It had tranny problems alright, and rear end problems!! I got @ $1800 more in it in parts and all seems to be good so far with @ 100 hrs since the work. Thanks again for the insight. Kent

[Log in to Reply]  [No Email]
Dr. Evil

09-11-2002 08:32:45




Report to Moderator
 Re: John Deere ? vs A-C D17 seriesIV in reply to Kent, 09-10-2002 21:03:57  
All the bickering aside.... D-17 Series IV was a good 4-bottom tractor....and would be most closely matched to a 3010/3020 in actual field performance. D-17 gave up little in features or options either.... Didn't have a diff lock avail. and no true Powershift was avail... but most had 3-point or Snap-Coupler plus 2 remotes, and the HI-LO range hand clutch was on them all. Very handy!



[Log in to Reply]  [No Email]
JD70Jim

09-10-2002 21:55:46




Report to Moderator
 Re: John Deere ? vs A-C D17 seriesIV in reply to Kent, 09-10-2002 21:03:57  
What John Deere tractor from ca. 1966 with ca. 57hp?
The John Deere 2020 Utility had 54 hp or so, the 2510 row crop had the same engine (and was an excellent tractor) and the 3020 (66-71hp)all come to mind. The 3020 is very common and has more of everything than the AC D17-IV. All of the John Deeres, being John Deere and all, are also much more expensive than a D17-IV. I would think that a good D17 could be had, wfe, diesel, for under $5000. All of the Deere's will cost more than that, some of then MUCH more. The 2020 is a fairly rare AND desireable utility, the 2510 are also faily low production AND very desireable working tractors, and a 3020 is one of the most sought after and expensive to buy tractors on the market. A nice, diesel, powershift, dual valve wfe 3020 can bring over $10,000 with ease. (Note: newer tractors bring more money, but a 3020 in good to excellent condition easily brings a LOT more than it's original NEW price) The gasoline versions of the John Deere tracors ARE quite a bit cheaper to purchase, althogh the difference will be less with the 2020 than the other two. You picked out one of the more desireable AC tractors also. The AC 170. 175, 180 and 185 tractors(which replaced the D17) are also pricey and will come close to some John Deere tractors in price.

[Log in to Reply]  [No Email]
John

09-11-2002 05:15:07




Report to Moderator
 Re: Re: John Deere ? vs A-C D17 seriesIV in reply to JD70Jim, 09-10-2002 21:55:46  
When did a 68 hp (AC 180) and a 75 hp (AC185) replace a 55 hp (AC D17)? That was the AC D19 class. The AC 170/175 according to all known information was the replacement of the AC D17, all 3 were in the 50-60 hp range. Depending on what you need for overall height, the 20(low tractor) or 30(high tractor) series will do either job with apx the same hp ranges. You won't be happy with the fuel consumption of the Deere over the AC in that range. I owned a D17 III and a 3020 and the JD took twice the fuel for about equal work. Traded the JD for a 185 AC and love it, it works circles around the 3020 and easier to manuever.

[Log in to Reply]  [No Email]
JD70Jim

09-11-2002 06:41:34




Report to Moderator
 Re: Re: Re: John Deere ? vs A-C D17 seriesIV in reply to John, 09-11-2002 05:15:07  
Manufacturers are replacing a unit of "X" hp with one that has "X+10" hp, all of the time. I am sure thet the similarity between "170" and "D17" would mean that they might be successor and anscestor but I also notice that the D17 was very popular and while I have barely ever even seen ONR 170, I see 180s ALL of the time since they are very common. Farmers naturally moved up in hp with new models. Take JD for example. Was the 3010 the replacement for the 730? Same hp range, right? WRONG! The 4010 in fact was the replacement for the 730. The 3010 replaced the 630. The currant replacement for the 4020 is the 7000 twenty series which runs to what? 155hp? The 200hp 4960 was a linear descendant of the 4020 also, even though this size is now covered by the 8000 series tractors (which are more like 5020 descendants).

[Log in to Reply]  [No Email]
mike

09-11-2002 06:10:36




Report to Moderator
 Re: Re: Re: John Deere ? vs A-C D17 seriesIV in reply to John, 09-11-2002 05:15:07  
You traded a 3020 for a 185 Ac,boy did you make a big mistake!!That AC just keeps dropping in
value the JD goes up.The 3020 might use a little
more fuel (I doubt half), but who cares its a
deductable expense.



[Log in to Reply]  [No Email]
John

09-11-2002 20:19:13




Report to Moderator
 Re: Re: Re: Re: John Deere ? vs A-C D17 seriesIV in reply to mike, 09-11-2002 06:10:36  
That's funny, I can sell or trade the 185 AC for $3000 more than I paid for it. The Orange AC D,100,6000,8000 & 4W series are holding or going up in value, the 8000's are selling for 2/3 of new price and they are 20 yrs old. They sure haven't lost much value. And if you look around, I sure see alot of pre D orange iron at shows and the price tags aren't cheap. The 7000 AC's seem to be the only ones losing value. And if you think 10.91hp/gallon is good at 71hp, I'll keep my 185 @ 15.25hp/gal at 75 hp. The 3020 had a love for the fuel barrel, the 185 doesn't. I went back to Deere 5 yrs ago because I wasn't sure what direction Agco was going to take and Deere can't even supply parts for a 5 yr old tractor. I can walk into my Agco dealer and walk out with most parts for my 185. Area Deere dealers use to keep a much better supply of parts, now they order for over night shipment and it is backordered or a 2 week wait. Deere has slid along ways in my area in the past ten years. One dealer trying to own every Deere store in the state and does the worst job of customer service I have ever seen. He wasn't the local dealer when I bought my Deere 5 yrs ago, they had service!

[Log in to Reply]  [No Email]
JD70Jim

09-12-2002 22:03:51




Report to Moderator
 Re: Re: Re: Re: Re: John Deere ? vs A-C D17 seriesIV in reply to John, 09-11-2002 20:19:13  
10.91 hphr/gal = gas engine

15.25 hphr/gal = diesel engine

The diesel fuel value for the John Deere is a little bit better than what you posted to say the least---say 14.76 hphr/gal (Nebraska test #940)!

Now let's price a tractor. 1970, JD 3020 D with wide front end, dual scv, powershift, new paint, new rubber, 7000 hours, excellent shape. $10,000-11,000!

What does the closest 1970, AC 185 equivilent bring? I'll guess that it doesn't bring that much. I'll guess $6500-7500.

[Log in to Reply]  [No Email]
tubba_JD420C_ny

09-13-2002 15:56:13




Report to Moderator
 Re: Re: Re: Re: Re: Re: John Deere ? vs A-C D17 seriesIV in reply to JD70Jim, 09-12-2002 22:03:51  
IT Price Guide for 2002 lists 1970 3020's equipped as you say (except for the powershift) for $4250 to $7520, but you are right in that I have seen an awful lot of 3020's as you described go for $10,000 to $12,000. Put your money into New Generation Deeres instead of the stock market.
AC 180's equivalent are listed at $3890 to $6070, so your estimate was pretty close. The Deere cost about $1,000 more new than the AC 180. Assuming prime condition, per IT The AC lost about 14% in value whereas the Deere lost about 6%, however, most of the 3020's I have seen have gone UP 50%. Just some of my ramblin'

[Log in to Reply]  [No Email]
John

09-13-2002 15:31:16




Report to Moderator
 Re: Re: Re: Re: Re: Re: John Deere ? vs A-C D17 seriesIV in reply to JD70Jim, 09-12-2002 22:03:51  
Please learn how to read the Nebraska Test results if you are going to quote them. 13.87 was the BEST results that NT would post for the Diesel 3020 #940. And if you read everything TWO RUNS WERE MADE to get that result. Do you really think that every JD tractor comes out of the factory at PEAK performance and PEAK economy when they had to tweak it that much at the tests. Funny how test #1044 doesn't have to be run twice to get peak performance. And a 270cid taking more fuel than a 301cid,hey that's 11% more engine taking less fuel. Or .26 gal. more for 3.44 hp less. Actual Nebraska Test Results. And find a 185 in that price range and it gets a new home fast. Sure don't see the 180/185 AC's sitting on dealers lots long like the 3010/3020. Local Salvage yard rarely get a 180/185 in and gets several 3010/3020 in per month. Get the facts straight Jim, I owned a 3020 and currently own a 185, can you say that you have had both.

[Log in to Reply]  [No Email]
G-MAN

09-14-2002 09:37:24




Report to Moderator
 Re: Re: Re: Re: Re: Re: Re: John Deere ? vs A-C D17 seriesIV in reply to John, 09-13-2002 15:31:16  
I don't think tractors are "tweaked" at the Nebraska tests, and they for sure don't tolerate any turned up tractors. It was not uncommon for tractors to be run more than once. When the 70 diesel was tested the first time, the fuel economy was so good that they thought something was wrong. They ran it the next day to back up the numbers, and it bettered the record it had set the day before, due to the additional run-in time. The tractors are tested over a period of several days, not all in one day, so results are also corrected for atmospheric conditions and the like. Do you think the reason you see more 3020s around than 180/185s could have anything to do with production numbers of the tractors? How many 180/185 tractors were built? The production numbers section on the side of this page shows around 25,000. They don't show 3020 production, but I know that it was many times that number, which could account for the difference in the number of each tractor around, don't you think? As far as JD tractors leaving the factory at peak performance, it's pretty much common knowledge around Deere dealerships that any new JD tractor is going to produce substantially more horsepower on the dyno than what it's rated. A new 245 horsepower JD tractor will generally have 260 or more horsepower on the dyno. I've seen it time and time again with many different models of new tractors.

[Log in to Reply]  [No Email]
John

09-15-2002 08:18:29




Report to Moderator
 Re: Re: Re: Re: Re: Re: Re: Re: John Deere ? vs A-C D17 seriesIV in reply to G-MAN, 09-14-2002 09:37:24  
Read the Nebraska Test result that Jim quoted. What is an adjustment? (Tweaked)States that adjustments were made to the 3020. No such statement was made of the 185AC. Does Deere send DOGS to the test so they can play with them? Again I will ask the same question of you I did Jim. Have you owned a 3020 D and a 185 Allis? I have, I have personal experience with both and sorry to deflate you but I found the AC to be a much better tractor. I still own a Deere too, which Deere can't support.

[Log in to Reply]  [No Email]
G-MAN

09-16-2002 07:42:13




Report to Moderator
 Re: Re: Re: Re: Re: Re: Re: Re: Re: John Deere ? vs A-C D17 seriesIV in reply to John, 09-15-2002 08:18:29  
Oh yes, I'm certain the the Nebraska test engineers turned their backs and allowed Deere personnel to work on the tractor. Normal adjustments are always made to test tractors. Have you ever been to the lab? I have - I've even helped prepare a tractor that was tested there, a Cat Challenger 75D, so maybe I'm a little more familiar with it than you are, but probably not. I also wouldn't own an Allis. I spent about 20 hours in a 7060 two weeks ago, and I'd rather push a Deere than drive that Allis. It's not hard to figure out why Deere's resale value is so much higher. The only D series Allis I've been around is my Dad's D-15, which seems to be a decent little tractor, but far from a Deere. It's been a year or so since the last 3020 I overhauled, but I'm sure I can keep up with you, if you want to start talking about the mechanics of the tractor. I'm glad that you like your Allis. I'm also very interested to hear how it is that Deere can't support your tractor. Are you the individual that posted on another subject saying that it took two weeks to get parts from your dealer? I responded to that post - it's not Deere, it's your dealer. Give me a part number for your tractor, and I'll tell you how soon you should have it.

[Log in to Reply]  [No Email]
G Taylor

09-11-2002 09:33:08




Report to Moderator
 Re: Re: Re: Re: John Deere ? vs A-C D17 seriesIV in reply to mike, 09-11-2002 06:10:36  
If the 3020 was worn to the point it really was using twice the fuel Time to at least rebuild the injectors and install both air cleaner elements with new. Many people keep track of fuel consumption by the number of times the fuel tank was filled rather than gallons actually used. Doesn't make sense when the tractor tanks are different sizes and HP output differs.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy