Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Discussion Forum
:

John Deere GM what size tire , Air breather dry element

Welcome Guest, Log in or Register
Author 
Stephen G

03-25-2002 12:16:21




Report to Moderator

Hi I am fifteen years old , and have a 1946 John Deere model (GM) tractor. I was wondering what size tire would be the best to do some stock Antique tractor pulling. Also what about the air breather ? Is a dry element conversion worth buying ? What if I took the oil out of the air breather just to pull, would that work just as good ? Any help would nice Thanks . stephen G .




[Log in to Reply]   [No Email]
George

03-26-2002 10:12:00




Report to Moderator
 Re: John Deere GM what size tire , Air breather dry element in reply to Stephen G, 03-25-2002 12:16:21  
Don't let these tractor pulling idiots talk you into butchering your tractor the way they have done with theirs!!!



[Log in to Reply]  [No Email]
Deere Puller

03-26-2002 11:48:43




Report to Moderator
 Re: Re: John Deere GM what size tire , Air breather dry element in reply to George, 03-26-2002 10:12:00  
I simply don't understand why you so-called 'collectors' can't stand the mere sight of a tractor puller - Adding a dry paper cleaner system without 'ruining' any of the original parts or appearance should not bother you one bit. Why not just say that given your choice, you'd leave it alone? Unfortunately, George, much like the correct police in general, you're the idiot.....



[Log in to Reply]  [No Email]
George

03-26-2002 13:04:26




Report to Moderator
 Re: Re: Re: John Deere GM what size tire , Air breather dry element in reply to Deere Puller, 03-26-2002 11:48:43  
Given the extremely limited IQ of most tractor pullers, I don't suppose you would understand. Wait until somebody's crank breaks, and the flywheel goes spinning off into the crowd, or the tractor driver (no great loss there), and injures or kills some people. Chopping up otherwise good tractors to make pulling tractors out of them is just plain stupid, but given the mentality involved, people like you will just keep on doing it. I'm not one of the "correct police", but you're right, I have a serious dislike of tractor pullers, and what they do to tractors.

[Log in to Reply]  [No Email]
Deere Puller

03-26-2002 13:29:04




Report to Moderator
 Re: Re: Re: Re: John Deere GM what size tire , Air breather dry element in reply to George, 03-26-2002 13:04:26  
George -

Point taken on the safety issue. I believe that many pullers take it for granted that their tractors will stay together, without ever really understanding the laws of inertia & how they apply to the gutted crankcases, flywheels, rods etc. Scatter blankets should be mandatory for all divisions above class "C" & the Deeres need to engineer a device to keep their exposed flywheels retained. Personally, I like to retain the completely stock appearance while making a bit more power under the hood, as these tractors are history's relics, to a degree.

However, when you paint all pullers with the same 12" wide brush that you appear to be fond of using, your message becomes lost. 'Cutting up' tractors needs to be well thought out, but in reality it is no different than people making street rods out of old cars, a hobby that I'm, sure you detest as well. Lighten up with the stereotyping, make clear non-threatening suggestions and perhaps you will be heard.

[Log in to Reply]  [No Email]
Deere Puller

03-26-2002 07:45:51




Report to Moderator
 Re: John Deere GM what size tire , Air breather dry element in reply to Stephen G, 03-25-2002 12:16:21  
A cheap (easy) way to have a paper element on your "GM" is to use the existing intake casting pipe and fab up a sealing plate that will connect via rubber hose at the top. You should be able to cram a 12" tall / 6" diameter cylinder element up under the hood the if you do it right. Make a bracket for your aircleaner stack (appearance only) or spend more time on the arrangement & make a true sealing canister that draws from the stack. The easy/cheap method will gain you significant flow over your oil bath & the more-effort canister will help to feed cooler air into the engine for a denser fuel charge. Did both on my "GM" at one point or another & in a hurry, would take the easy way out, as it gives you the most bang for your initial buck. Good luck

[Log in to Reply]  [No Email]
G Taylor

03-25-2002 20:50:23




Report to Moderator
 Re: John Deere GM what size tire , Air breather dry element in reply to Stephen G, 03-25-2002 12:16:21  
Removing the oil from the aircleaner still leaves the middle 1/4 to 3/4 mesh area loaded with oily mud accumulated for the past 57 or so years. If nothing else drill the spot welds & boil the mesh clean before re-installing it. You won't believe it untill you see it, how much silica gets set into the mesh.



[Log in to Reply]  [No Email]
burns

03-25-2002 19:24:38




Report to Moderator
 Re: John Deere GM what size tire , Air breather dry element in reply to Stephen G, 03-25-2002 12:16:21  
In W. PA the rear tire is usually limited to 15.5x38 or 14.9x38 in the stock classes. If your G is fairly stock, I would think it will be tough to maintain a decent tire spin with the 18.4x38's. Of course the type of track has a lot to do with what can be used.

As far as the air cleaner, you can have someone like Renaissance tractor convert the canister to accept a paper filament or have someone like Steve Crum build a staight through intake pipe. The pricing is about the same but you will either need to run raw unfiltered air or install a filter above the hood.

[Log in to Reply]  [No Email]
JD G GUY

03-25-2002 13:59:51




Report to Moderator
 Re: John Deere GM what size tire , Air breather dry element in reply to Stephen G, 03-25-2002 12:16:21  
dnt know what to tell you bout the air cleaner but if you have the origional rims on it they are probly 12"x38 rims it would be best to use a 13.6"x 38 tire so the bead is set correctly to the rim unless you want to get new rims for a wider tire.



[Log in to Reply]  [No Email]
Stephen G

03-25-2002 14:32:37




Report to Moderator
 Re: Re: John Deere GM what size tire , Air breather dry element in reply to JD G GUY, 03-25-2002 13:59:51  
I have 18.4 38 tires on 16 inch rims on the tractor right now . I was thinking that I might possibly be able to trade tires and rims with someone . My tires are pretty new . One I bought last year, and the other one was on the tractor, but it is in just as good shape. I live in Maine. Thanks Stephen G



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy