Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

620 Blowby help Clooney or anyone else

Welcome Guest, Log in or Register
Author 
DG

12-02-2003 14:00:27




Report to Moderator

In reference to the post by clooney, link is below.

Link

I have a 620 that I recently purchased, and I had it working on the dyno the other day and I noticed that it seemed to "puff" pretty good out of the breather pipe once it got warmed up. I took it off of the dyno when I saw this, and it stopped after a little bit.

Now it was pretty cold the last time that I shut it off when it was warmed up, and it may have just been condensation (I wish that I would have smelled the situation out better).

The guy that sold it to me told me that he compression tested it and it was around 125 per side. I tend to believe him because the tractor starts very good (even when cold), and when you shut it off the engine rocks back as it is just about to stop when it comes up on compression. There is no hint of oil smoke from the exhaust pipe either.

My whole question is does the 620 have this air circulation system that you mentioned in the above post and could this "smoke" just have been condensation? I am new to the 2 cylinder game.

Thanks in advance.

DG

[Log in to Reply]   [No Email]
Ron

12-03-2003 00:26:10




Report to Moderator
 Re: 620 Blowby help Clooney or anyone else in reply to DG, 12-02-2003 14:00:27  
If it is moisture venting, it may take a couple of HOURS of good work, to dry out the tractor, and for the vapor to slow down... Work it GOOD, before you decide to tear it down...!! Some "Breathing" is normal anyway... If it don't use a quart of oil in a good day's work, and don't smoke, it is most likely OK...!!



[Log in to Reply]  [No Email]
buickanddeere

12-02-2003 17:55:25




Report to Moderator
 Re: 620 Blowby help Clooney or anyone else in reply to DG, 12-02-2003 14:00:27  
All piston engines have blowby from the combustion chamber into the crankcase. It's just a matter of how much there is, how much it looks like to the observer and how much you want to put up with. The two cylinder crankcase air pump adds to the perceived airflow.



[Log in to Reply]  [No Email]
tom

12-02-2003 18:50:54




Report to Moderator
 Re: Re: 620 Blowby help Clooney or anyone else in reply to buickanddeere, 12-02-2003 17:55:25  
Buick&deere,

Howdy,

How much is an acceptable amount of blow-by smoke from the breather cap? I have an MT and I notice the smoke coming from there, especially since I do not have the hood or grille on because I want easy access as needed.

Also, I do not recall reading anything about a crank-case air pump on my MT. I guess since this would not inpact any blow-by smoke, "what I see is what I get".

Thanks for your opinion and anyone else's.

regards,
tom

[Log in to Reply]  [No Email]
buickanddeere

12-03-2003 00:15:26




Report to Moderator
 Re: Re: Re: 620 Blowby help Clooney or anyone else in reply to tom, 12-02-2003 18:50:54  
The Waterloo built 620 we were speaking of is much different than the Dubuque "M". No crankcase fan. Should see what blows/leaks out of my 435 but that's a different situation. Ambient air temp,humidity and the background on the other side of the breather cap can make vapours readily visible. If the crankcase has some condensation/gasoline in the oil more vapour will be visible as she gets fully warmed up. If compression & oil consumption is acceptable than don't worry about it. Even if it's blowing enough out the breather to fly a kite over top of the tractor. Is it worth the cost of a proper rebuild?

[Log in to Reply]  [No Email]
ChuckW

12-02-2003 14:51:26




Report to Moderator
 Re: 620 Blowby help Clooney or anyone else in reply to DG, 12-02-2003 14:00:27  
I've torn down several tractors and even with good compression you generally will find top grove wear and occassionally a broken ring. The pistons used in these were an aluminum alloy and they generally have wear more so than the old cast iron type pistons. If I had much of a concern I would rering it and if necessary replace the pistons. Doing it yourself you could probably do in the neighborhood of $400-500. Sounds like the smoke somewhat bothers you and to get a better ring seal you will probably need to renew those.

[Log in to Reply]  [No Email]
Clooney

12-02-2003 14:10:27




Report to Moderator
 Re: 620 Blowby help Clooney or anyone else in reply to DG, 12-02-2003 14:00:27  
DG, you ask...."My whole question is does the 620 have this air circulation system that you mentioned in the above post and could this "smoke" just have been condensation?"....>>Yes, your 620 has a crankcase ventilator pump..& yes it could have been condensation..

~Those tractors do smoke a little out the vent while working hard.. Run it a while & see if the vent smoke clears up ...

~If it doesn't diminish after a good workout you might want to run a HOT leakdown test on it, that will tell the story..... .

[email protected]

[Log in to Reply]  [No Email]
JD620

12-02-2003 15:53:25




Report to Moderator
 Re: Re: 620 Blowby help Clooney or anyone else in reply to Clooney , 12-02-2003 14:10:27  
Clooney, My dad has a JD 620. And when he pulls it, there seems to be alot of smoke or something come out the crankcase breather tube. We just thought it needed a set of rings. What do you mean when you say do a hot leakdown test? Thanks for any info. JD620



[Log in to Reply]  [No Email]
mike f

12-02-2003 19:16:48




Report to Moderator
 Re: Re: Re: 620 Blowby help Clooney or anyone else in reply to JD620, 12-02-2003 15:53:25  
I think that is pretty much normal for it, my dads 620 has some and the motor has about 5 hours on it now, I do think it will diminish some, but I have seen many other 620's that do this and they ran really well, now my 60 hardly ever shows any out it's crankcase vent, but it probably varies from tractor to tractor, and yes all the two cylinders from about 47 or 48 have a vent pump in the fanshaft near the governor, I cant say for the dubuque tractors as I dont mess with those. I dont think that G's ever had a pump either.

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy