Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Discussion Forum
:

Should I take my B apart?

Welcome Guest, Log in or Register
Author 
Bill Oakes

03-06-2001 12:14:31




Report to Moderator

I am working on my first John Deere, a 48 B. It didn't run when I got it; had been sitting about 6-7 years. Had very low compression in one cylinder. I have removed all the sheet metal and will flush out the gas tank well. I pulled the head and had the valves ground and the machinist said it all looked good. My big question now is should I pull it apart further. The cylinders don't look bad. Should I put it back together and hope for the best or should I tear it apart further checking for other problems. This will not be a working tractor; just for fun - show and parades. I am trying to make things decent without being a perfectionist. What would you more experienced guys advise??? Thanks for the help, Bill

[Log in to Reply]   [No Email]
Bill Oakes

03-07-2001 17:09:45




Report to Moderator
 Re: Should I take my B apart? in reply to Bill Oakes, 03-06-2001 12:14:31  
Thanks for the advise guys. I will pull it apart and see what's in there. Better safe than sorry, right? Thanks again, Bill



[Log in to Reply]  [No Email]
luckydog

03-07-2001 15:37:38




Report to Moderator
 Re: Should I take my B apart? in reply to Bill Oakes, 03-06-2001 12:14:31  
Hi my friend-I believe I would take the crankcase cover off and take a look/see. Turn the engine over, look at the main bareings to see if you can see any rust pits. If you had low/comp on one piston you could have stuck rings. If not much ridge at the end of the sleeve I think I would pull the pistons and clean and inspect like mentioned below, put new rings in and put back together. Wish I was there to help!! Good luck luckydog

[Log in to Reply]  [No Email]
gary

03-06-2001 20:09:29




Report to Moderator
 Re: Should I take my B apart? in reply to Bill Oakes, 03-06-2001 12:14:31  
Bill,
I am in the same situation that you are, my 48 smokes a bit and has low compression on one cylinder. It's just for fun too, but I would like it to run right, which is more important to me than aesthetics. The only thing is, all that work runs into money pretty quick. Whatever you do, would you keep me posted, as far as how much you spent, and what you found (and learned) along the way. I am sure others would like to know too. You got some excellent advice, even from ZZ Top, who I really couldn't follow all that well, but I have a feeling he is either way ahead of his time or far behind, and I don't think he cares one way or the other.
Good luck, keep us posted!

[Log in to Reply]  [No Email]
ZZ top

03-06-2001 15:52:09




Report to Moderator
 Re: Should I take my B apart? in reply to Bill Oakes, 03-06-2001 12:14:31  
I am working on my first guitar, a 48 double pedal g-strap merauder. It didn't run when I got it; had been sitting since 1800 b.c. Had very low compression in vlave. I have removed all the sheet metal and will flush out the cantalopes as well. I pulled the head and had the valves destroyed and the machinist said" what are you doing you idiot". My big question now is should I smash it even more. The cylinders don't look bad. Should I put it back together and hope for the best or should smash them checking for other problems. This will not be a working tractor; just for fun - parachute drops etc. I am trying to make things decent without being a pycho. What would bill clinton think???

[Log in to Reply]  [No Email]
Kris

03-07-2001 10:03:30




Report to Moderator
 Re: Re: Should I take my B apart? in reply to ZZ top, 03-06-2001 15:52:09  
Hey ZZ you might want to be careful with the Parchute drop. I heard somtimes tractors don't land on all four feet!


Kris



[Log in to Reply]  [No Email]
Thats Funny.!! (NT)

03-07-2001 05:02:22




Report to Moderator
 Re: Re: Should I take my B apart? in reply to ZZ top, 03-06-2001 15:52:09  
NT



[Log in to Reply]  [No Email]
Chuck W.

03-06-2001 15:10:15




Report to Moderator
 Re: Should I take my B apart? in reply to Bill Oakes, 03-06-2001 12:14:31  
have reworked many of these tractors. My suggestion would be to hone the cylinder ring grove before trying to remove the pistons. Also check your shims before overhaul, I believe they are 3/1000 in thickness. You should remove one shim upper and lower then retighted. If rod binds to the crank, replace the shims upper and lower till it is free. Do this before removing the pistons as you will not have the extra drag of new rings. I wouldn't recommend pulling the block just a hone job. Be sure to install rings properly and get all the carbon from the lands in the pistons. Good luck

[Log in to Reply]  [No Email]
Clyde Scott

03-06-2001 13:53:42




Report to Moderator
 Re: Should I take my B apart? in reply to Bill Oakes, 03-06-2001 12:14:31  
Bill:
I had the same situation as you with my first Deere.. After I had pulled the head off, because I had broken the bolts off in it removing the manifold that was rusted thru, I thought since I was this close to the pistons, a new set of rings was in order. Glad I did because after pulling the pistons, and honeing the block, I discovered the babbit bearings were shot on the crank.. Pulled the crank out, had it ground, had the rods re-babbitted, new main inserts and all back together. The babbit bearings to crank journals had about 0.010 slop in them and no more shims to remove.. I'm thinking this would have led to much bigger problems later in the life of this ole 50 B. If I were you, I would at least check the rod journals to crank clearence and the slop in the main bearings before I put her back together.
Clyde Scott - Moultrie, GA.

[Log in to Reply]  [No Email]
Pull~Dog

03-06-2001 13:28:44




Report to Moderator
 Re: Should I take my B apart? in reply to Bill Oakes, 03-06-2001 12:14:31  
I would say gp for it. You have to remember that john deere two cylenders were made in a era where engines were new. Thus. it was costructed for anyone to fix. Dont get me wron all engins are complicated but the old JD 2 cylenders are fairly easy to work witht he engine. We had one that was stuck, It was a 1950 B. we a;so were in a A john DEERE. I would have to say go for it... Shohn Busald-15yrold-Indiana

[Log in to Reply]  [No Email]
Mike

03-06-2001 12:58:04




Report to Moderator
 Re: Should I take my B apart? in reply to Bill Oakes, 03-06-2001 12:14:31  
If you already have the head off, pulling the jug is only 4 nuts,pulling the top cover and disconecting the rods away. If I was in your position I'd continue on and pull the jug and at least have it honed out and put in a new set of rings. Good luck,Mike



[Log in to Reply]  [No Email]
khh

03-06-2001 17:46:47




Report to Moderator
 Re: Re: Should I take my B apart? in reply to Mike, 03-06-2001 12:58:04  
If you put in new rings don't forget to get a ridge reamer and cut the ridge in the cylinder or the new rings will hit the ridge.



[Log in to Reply]  [No Email]
That's what honing does, duh!

03-07-2001 10:26:17




Report to Moderator
 Re: Re: Re: Should I take my B apart? in reply to khh, 03-06-2001 17:46:47  
READ THE POST!



[Log in to Reply]  [No Email]
Duh

03-07-2001 12:12:34




Report to Moderator
 Re: Re: Re: Re: Should I take my B apart? in reply to That's what honing does, duh!, 03-07-2001 10:26:17  
Ridge reaming and honing are separate operations with separate tools. Ridge reaming is done first and then honing. The presence of a ridge at the top of the cylinder indicates a need to carefully measure the clylinder for size, taper and roundness. If out of tolerance (read the manual), rebore.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy