Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

40 T steering

Welcome Guest, Log in or Register
Author 
Warren

11-18-2003 05:01:21




Report to Moderator

my 1955 40T has lots of play in the front end and i have tried several times to adjust the steering i have tightened the set screw on top of the pedestal and it never seems to help...when i drive it it does ok sometimes but when i hit a rough area of ground you can see the front wheel just wobble and it has quite a bit of play in it...what needs to be replaced and how do i fix it? Thanks, Warren...Tupelo Mississippi

[Log in to Reply]   [No Email]
Wayne in Tn.

11-18-2003 12:52:48




Report to Moderator
 Re: 40 T steering in reply to Warren, 11-18-2003 05:01:21  
Warren, I am assuming you have a tricycle front end. First check those pins that ride in the worm gear. (Underneath the cap where you are trying to adjust the play) If those pins are worn, they can be purchased from Deere. They have to be peened in with a ball peen hammer. Check the wheel bearings for excessive play. Next, with the front wheels sitting on concrete, grab one with both hands and try to roll it back and forth. If you see any motion up in the pedastile, then its time to rebuild the pedastile. I have done this lately and all the parts to rebuild it cost about $115 from Deere. There are bearings, seals and thrust washers in there. Once this is rebuilt, you will be amazed at the difference in the way it drives. Also there is a splined coupler in there that could be worn out. Also check where the steering rod connects to the steering box (on top of radiator) Of course you will need the hood and nose off, in order to check everything. If you have a wide front---check tie rods and wheel bearings

[Log in to Reply]  [No Email]
Henry J

11-18-2003 06:34:32




Report to Moderator
 Re: 40 T steering in reply to Warren, 11-18-2003 05:01:21  
Warren

I hope you don't find everything is worn out :(.

I would start by taking the top off of the pedistal and seeing if the worm gear and the (Whatever it is) pin that fits in the worm is serviceable.

From there rotate the steering wheel back and forth (the play part) and check the coupling going to the pedistal.

Watch the top of the pedistal shaft when you rotate the slop back and forth an see if it moves back and forth some and the front wheels don't. There has to be a coupler down there somewhere.

Sad to say, that if someone has not done any component repairs, it most likely is a combination of several wear places.

PS: If you find the 90 degree gear box worn, low on oil or needing repair, I would recommend filling it with JD Corn Head Grease. That stuff won't leak out the bottom of the box where the vertical shaft enters.

Good Luck

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy