Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

Bridgeport Milling Machine-Off topic

Welcome Guest, Log in or Register
Author 
Paul

11-08-2003 10:08:13




Report to Moderator

I am looking at purchasing a Series 1 Bridgeport milling machine from a used equipment supplier. It is variable speed built in 1980. I am not familiar with the machine and would like some advise as to what to look for as far as wear and condition. the machine is not under power but he guarentees it to work. also is there a discussion board on machining etc anyone is aware of. thanks Paul




[Log in to Reply]   [No Email]
HMan

11-09-2003 08:02:03




Report to Moderator
 Re: Bridgeport Milling Machine-Off topic in reply to Paul, 11-08-2003 10:08:13  
Paul, I'm a tool and die maker by trade and our shop has 3 Bridgeports, 1 ezy-trac,1 variable speed,1 step pulley. $4500 sounds high to me,unless it's been factory reconditioned. You can get a new,220v, step pulley Enco, with power feed and a dro for about that $. For home, light use I like a step pulley, they are much cheaper and easier to repair. To answer your question, look at the ways, they should look like they have dull "feathers" on them, not bright. Put a dial indicator on the quill with the stem on the ways and feed the table up and down and back and forth, both X,Y and Z. See how much slack ("end play") it has in the table. I would not touch it unless I ran it, have him hook it up and run the motor through the speed range in high speed and back gear. It should be smooth with no growls. Make sure the power down feed works. As stated above,it sounds high to me, in my area it sounds like $2500 - $3000. Hope this helps you, HMan

[Log in to Reply]  [No Email]
Donny-B

11-09-2003 19:22:17




Report to Moderator
 Re: Re: Bridgeport Milling Machine-Off topic in reply to HMan, 11-09-2003 08:02:03  
Paul, That price should include power feed and a DRO. $4500 is a bit steep for a base machine. The market is flooded with machinery as there have been a decline in machine shops over the past 5 years. HMan's advice is right on the money. Have the machine powered up before you buy. Listen for any loud bearing noise in both hi and back gears. Check table play. Look at the screws for wear. Check for any spindle spline wear. I would also suggest having an experienced machinist take a look at it and crank the handles. A Bridgeport in good running condition in PA. runs $2000-$3500. (about the price of a new Enco) Good Luck.

[Log in to Reply]  [No Email]
Paul

11-09-2003 10:38:53




Report to Moderator
 Re: Re: Bridgeport Milling Machine-Off topic in reply to HMan, 11-09-2003 08:02:03  
Thanks for the info guys. I am going to look at it 11/10/03.



[Log in to Reply]  [No Email]
Dr.EVIL

11-09-2003 09:51:11




Report to Moderator
 Re: Re: Bridgeport Milling Machine-Off topic in reply to HMan, 11-09-2003 08:02:03  
I agree with everything You say, especially on the price. If the machine has a smaller table I'd even say $2000 would be fair if it's in good condition. Costs a lot of $$$$ to get a Bridgeport back into shape once it's wore out, that's IF You can find someone qualified to do the work.



[Log in to Reply]  [No Email]
Paul

11-08-2003 17:37:55




Report to Moderator
 Re: Bridgeport Milling Machine-Off topic in reply to Paul, 11-08-2003 10:08:13  
It is set up for 3 phase and I would have to buy a converter from them which runs 150.00 It does have a vise with it. asking 4500.00 but told me to make offer.



[Log in to Reply]  [No Email]
Crum

11-08-2003 19:49:08




Report to Moderator
 Re: Re: Bridgeport Milling Machine-Off topic in reply to Paul, 11-08-2003 17:37:55  
Paul, Don't let the 3 phase scare you, The converter you mentioned is likely a static converter, probably a phase-o-matic. I've used these for years mainly on 5 horse and smaller motors. These are basically a set of capacitors in a neat, simple to wire box that has 220-240 volt single phase input and 230 volt 3 phase output, one leg, the generated leg cannot not be hooked to to the machine tool's control voltage feed. This leg has only voltage with no amp capacity. The motor this converter runs will only run at 66% of rated horse power ie; a 3 horse motor will only produce 2 horsepower. But in 99% of the cases 66% of capacity works just fine. I also installed a 15 horse roto-phase as my machine tools got bigger, a motor will run at 95% of rated horsepower on this system. This type system should not be hooked up to less than a 200 amp service and requires a 3 phase breaker panel and wiring for distribution, A roto will produce a "wild" leg that is usually 240 volts with the other 2 legs being 120 volts the motor this runs will equallize the voltage but don't hook control voltage to this leg! The bucks get bigger with this system in a hurry. Used 3 phase motors are dirt cheap at most junkyards and the worst they usually need is 20 bucks worth of bearings. $4,500 doesn't sound too bad if the machine is in good condition with no roughness or losseness in the table, or spindle. The vise is a gimme, most but the most precision operators buy an Enco or other import new for about $150 and used top of the line vises are well used. Good luck.

[Log in to Reply]  [No Email]
Jim

11-09-2003 06:16:43




Report to Moderator
 Re: Re: Re: Bridgeport Milling Machine-Off topic in reply to Crum, 11-08-2003 19:49:08  
Crum you are right on the phase converters. If it is a smaller mill the cheaper converters will work ok. I prefer building a rotary converter out of a good 240 volt 3 phase motor. I have ben running a 400 amp wire welder since 1981 on one that I made out of a 20 hp motor with no problems. I like the older "U" frame motors because they have a lot of copper and a 5 horse is the size of a 20 horse new motor. I have built several of there and am in the process of building one for for a guy that just purchased a lathe. These things will just sit in the corner and run forever and make all the 3 phase you will need.

[Log in to Reply]  [No Email]
Van

11-08-2003 17:06:21




Report to Moderator
 Re: Bridgeport Milling Machine-Off topic in reply to Paul, 11-08-2003 10:08:13  
One phase or three?



[Log in to Reply]  [No Email]
Kent of SW MO

11-08-2003 14:26:25




Report to Moderator
 Re: Bridgeport Milling Machine-Off topic in reply to Paul, 11-08-2003 10:08:13  
Make sure it uses the R-8 collet. What price is being ask? Is any tooling included.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy