Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

Any harm to pull start JD Model B?

Welcome Guest, Log in or Register
Author 
Edward

11-04-2003 08:20:06




Report to Moderator

Read someplace that pull starting a two-cylinder was not recommended. Is this factual? If it is not harmful, what gear is recommended?




[Log in to Reply]   [No Email]
Frank M.

11-05-2003 19:16:47




Report to Moderator
 Re: Any harm to pull start JD Model B? in reply to Edward, 11-04-2003 08:20:06  
We pull started a 720 several times when I was a kid. Never seemed to hurt anything. How about the H? Since it drives off the camshaft, it looks like it would be awful rough on the timing gears. Anybody had any trouble with this? I pull started mine once, and got by with it, but I was afraid I might mess something up. Thanks for any input.
Frank M.



[Log in to Reply]  [No Email]
buickanddeere

11-05-2003 06:35:10




Report to Moderator
 Re: Any harm to pull start JD Model B? in reply to Edward, 11-04-2003 08:20:06  
They tend to tear up the driveway gravel more than pulling a four/six cylnder. The damage occurs when the tow chain is attached to some fragile part of the front axle/steering and yanked. The main hazard is when the wife if operating the tow vehicle. Give them 10 feet of slack chain and they will use it all to get a running start before jerking it tight and whiplashing the driver of the dead vehicle.

[Log in to Reply]  [No Email]
Loren from MN

11-04-2003 21:19:43




Report to Moderator
 Re: Any harm to pull start JD Model B? in reply to Edward, 11-04-2003 08:20:06  
Have pull started for 40+ yrs. Never had a problem. To our amazement though, have a 50 "A" that hadn't been run for quite some time. Dead battery. Engine loose. Tried jumping, didn't work. Pulled it with the 4010, and it started before we were out of the shed, maybe 10 ft. or so.



[Log in to Reply]  [No Email]
David Bacon

11-04-2003 20:03:12




Report to Moderator
 Re: Any harm to pull start JD Model B? in reply to Edward, 11-04-2003 08:20:06  
I have lived on the 2 cylinders all my life and never heard that before. I would be very interested in a real good reason. I have read all the posts so far and have found no credability in any of the coments thus far. I grew up with two brothers that between the three of us gave the old girls every acid treatment a boy can think of. The flywheel start tractors were ALWAYS PARKED ON A HILL SO US YOUNG ONES COULD START THEM. As far as gear lash---think about a bailer with a load of bales and the plunger rocking as it kicks the tractor from behind, then puts a tug on her again at 550 RPM's (gear lash far more than pull starting) all day for weeks on end. I do not defend the green as I collect every brand I can get my budget wrapped around. I do know the Oliver's in the 1750 (not sure)range can not be towed because the motor must run to pump oil to the transmission. Dave NE Iowa

[Log in to Reply]  [No Email]
Dan Looney

11-05-2003 08:02:26




Report to Moderator
 Re: Re: Any harm to pull start JD Model B? in reply to David Bacon, 11-04-2003 20:03:12  
Dont pull with a rope! If the motor is locked, something has to give when you drop the clutch. THE ROPE CAN STRETCH THEN SNAP CAUSING A VERY DANGEROUS SITUATION FOR BOTH OPERATORS, AS WELL AS BYSTANDERS.I KNOW!!!!



[Log in to Reply]  [No Email]
Mike M

11-04-2003 18:23:39




Report to Moderator
 Re: Any harm to pull start JD Model B? in reply to Edward, 11-04-2003 08:20:06  
Just don't pull one that the engines stuck and watch out for a cylinder full of gas as liquid does not compress. Bent rods and broken gears can result. And never ever ever pull start a newer John Deere with the high and low shuttle [rabbit and turtle]. If you don't beleive me ask the guy down the road with the 2840 that thought replaceing the starter would take up too much of his busy time and cost too much. That was at least a $3000.00 pull start. Tore the high low all up.

[Log in to Reply]  [No Email]
YOOPER DEERE

11-04-2003 17:18:11




Report to Moderator
 Re: Any harm to pull start JD Model B? in reply to Edward, 11-04-2003 08:20:06  
I have always pull started mine in the spring when I first start them for the summer, but I have a new way of starting them now, I have a belt, like the kind they used on threshers and I just start a tractor that I know is going to start right away and hook it up to one that is stubborn and it starts them right away!



[Log in to Reply]  [No Email]
Paul from MI

11-04-2003 16:48:37




Report to Moderator
 Re: Any harm to pull start JD Model B? in reply to Edward, 11-04-2003 08:20:06  
I have pull started every JD I've owned at one time or another. Every time it was because there was some kind of problem that kept it from starting by hand. Could be ignition, plugs, carb, cracked head, or just plain flooded and no patience left, to name only a few that I have encountered. If you're pulling it on a regular basis you have some other problem that you need to address. Any one of mine will start on 2-3 pulls unless it's around 0 degrees. I would do some looking before pulling, but it won't hurt anything.
Paul

[Log in to Reply]  [No Email]
Roger

11-04-2003 14:02:09




Report to Moderator
 Re: Any harm to pull start JD Model B? in reply to Edward, 11-04-2003 08:20:06  
We used to pull the G a lot until we found out why it was so hard to start with the starter, now it starts on the second revolution



[Log in to Reply]  [No Email]
joe

11-04-2003 13:43:25




Report to Moderator
 Re: Any harm to pull start JD Model B? in reply to Edward, 11-04-2003 08:20:06  
Don't try to pull one that is stuck and attempt to free it up, as you could bend rods, break tranny gears, ect.



[Log in to Reply]  [No Email]
zane

11-04-2003 13:32:29




Report to Moderator
 Re: Any harm to pull start JD Model B? in reply to Edward, 11-04-2003 08:20:06  
If it was harmful there wouldn't be very many around.



[Log in to Reply]  [No Email]
nightowl

11-04-2003 12:42:56




Report to Moderator
 Re: Any harm to pull start JD Model B? in reply to Edward, 11-04-2003 08:20:06  
I THOUGHT THAT WAS THE ONLY WAY TO GET A JD TO START!!!!! !!!



[Log in to Reply]  [No Email]
ChuckW

11-04-2003 11:21:30




Report to Moderator
 Re: Any harm to pull start JD Model B? in reply to Edward, 11-04-2003 08:20:06  
I've been around these tractors for 58 years and this is a new wrinkle for me...why would it hurt gears going one way rather than another way...put it in about 3/4 and go to it....the only thing I see you have to watch is not to run over the puller....



[Log in to Reply]  [No Email]
CLW

11-04-2003 09:41:22




Report to Moderator
 Re: Any harm to pull start JD Model B? in reply to Edward, 11-04-2003 08:20:06  
We use 6th gear and if using a truck, we pull about 5-6 MPH. If using another tractor, 4th is fast enough for the pulling tractor. We never fully engage the clutch on the tractor being pulled. Never heard of harm to tractor pull starting it.
CLW



[Log in to Reply]  [No Email]
Bguy

11-04-2003 09:05:02




Report to Moderator
 Re: Any harm to pull start JD Model B? in reply to Edward, 11-04-2003 08:20:06  
As long as you are careful as far as what you attach your pull strap/rope to and don't pull it too fast, it is perfectly safe to pull start these old 2 cylinders. If I have one that's being contrary to start I usually roll it down the hill as you don't have to go very fast or very far to turn one over enough for it to start. I know before I had my mag rebuilt, if it turned over a half dozen times and didn't start, it probably wouldn't start at all with out further attention.

[Log in to Reply]  [No Email]
Dale W

11-04-2003 09:00:59




Report to Moderator
 Re: Any harm to pull start JD Model B? in reply to Edward, 11-04-2003 08:20:06  
I'm sure over the years we have all pull started a few tractors, however an old two cyl. mechanic told me not to pull the two lungers. He said that when you are pulling it, all the gear lash is applied from the ground to the engine, when the engine fires, it instantly reverses that gear lash to come from the engine. Depending on the amount of wear there can be quite a bit of gear lash, and major damage can occur. I always run a belt from one tractor to the other, that way if it doesn't take right off, you can tinker with the carb, etc. as it turns over. Just my $.02 worth Good luck.

[Log in to Reply]  [No Email]
SamH

11-04-2003 08:35:15




Report to Moderator
 Re: Any harm to pull start JD Model B? in reply to Edward, 11-04-2003 08:20:06  
Pulling or rolling down a hill in a high gear has never hurt any tractor I've owned, but be careful to not over rev the engine. I saw a guy really mess up the engine of an "A" one time by pulling it down the road behind a pickup truck.



[Log in to Reply]  [No Email]
Alvin n Ms.

11-04-2003 14:59:42




Report to Moderator
 Re: Re: Any harm to pull start JD Model B? in reply to SamH, 11-04-2003 08:35:15  
I think they were more concerned about someone getting hurt. You got to admit those hand operated clutches, were not state of art. What if it got hung up and you ran over the puller? Has anyone ever heard of anything like that ? Did you ever try to plow up the low side of a terrace with one of those little jewels ? Was a real widow maker on hillside land.



[Log in to Reply]  [No Email]
Ron

11-04-2003 19:11:37




Report to Moderator
 Re: Re: Re: Any harm to pull start JD Model B? in reply to Alvin n Ms., 11-04-2003 14:59:42  
Why do you say they were "widow-makers"..?? The 2-cylinder JD's had a LOWER Center of Gravity than any other row-crop tractor made at that time...!! And... I really do believe that the Hand Clutch was safer than any FOOT clutch..
Now---IF you are talking about that clutch lever hitting you in the KNEE...!!!! I AGREE...it feels like it has killed ya...!!! Ron.



[Log in to Reply]  [No Email]
Dr.EVIL

11-05-2003 08:02:25




Report to Moderator
 Re: Re: Re: Re: Any harm to pull start JD Model B? in reply to Ron, 11-04-2003 19:11:37  
If hand clutches are so much better why is the grill of every hand-clutch Deere that hasn't been restored dented up from running into something? And I swear EVERYONE Who's ever operated a hand clutch deere uses the belt pulley brake to stop the tractor right? And Deere made that little friction pad So easy to replace too. Hope the guy that designed the bendable clip-on design pad retired very wealthy to someplace VERY nice.

[Log in to Reply]  [No Email]
David Bacon

11-05-2003 16:36:51




Report to Moderator
 Re: Re: Re: Re: Re: Any harm to pull start JD Mode in reply to Dr.EVIL, 11-05-2003 08:02:25  
I sure do not mean to break foul on you in any way, but sure are intrested in the research you remark on. So you understand I have numerous colors, and do not favor any brand any at all. Again--no insult intended in any shape size or form. Dave NE Iowa



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy