Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

1950 B Starter Question

Welcome Guest, Log in or Register
Author 
elcajonfarms

05-10-2008 08:43:08




Report to Moderator

My 1950 B has been sitting outside a couple of years, and I"m trying to get it running again. Even with a new battery, I can"t get the starter to engage and turn over. I can manually press the switch on the bottom of the starter and it spins just fine, but depressing the starter foot button from above results in only a "clunk" and nothing more. I"m assuming the problem is in the starter clutch assembly, either the clutch splines are not properly aligned with the flywheel or the clutch is frozen or rusted in place. Does anyone have any suggestions on what to do short of tearing the whole starter assembly apart? Is there an adjustment of the mechanical linkage that could correct this problem, or is it probably in the starter clutch itself?

[Log in to Reply]   [No Email]
johns48jdb

05-10-2008 16:17:21




Report to Moderator
 Re: 1950 B Starter Question in reply to elcajonfarms, 05-10-2008 08:43:08  
first you need to determine if the starter will engage with it off the tractor. if that works then you need to address the teeth interface between the bendex and the ring gear. i welded me up just a little tool that looks like a wrench to cut your water meter on and off with so i could just tweak the location of the flywheel a little bit when needed. not something to try and crank it with. after i saw it crank right away after moving the flywheel a tad and then every thing worked. i solved my problem by using a die grinder to bevel the teeth on the fly wheel ever so ease and not very deep. even now sometimes i have to hit the switch with my foot a time or two to make it engage, but it beat what it was doing.

[Log in to Reply]  [No Email]
M w J

05-10-2008 10:46:43




Report to Moderator
 Re: 1950 B Starter Question in reply to elcajonfarms, 05-10-2008 08:43:08  
That starter has a switch rite on the starter and the contacts get wore you can make it turn when you push that switch . But when you step on the starter pedel it also engages the starter drive gear.What happens is the drive gear engages all the way before the switch makes good solid contact so it will ark and loose contact You most likly need the little switch new. Sometimes the copper bolt on the starter gets wore down and needs to be replaced . MIKE

[Log in to Reply]  [No Email]
RobMD

05-10-2008 10:20:23




Report to Moderator
 Re: 1950 B Starter Question in reply to elcajonfarms, 05-10-2008 08:43:08  
spray some WD 40 on the bendix if you can, somehow. And i'll agree with BOB, it'll eventually come free once you get it going and polished up again. Rotate that flywheel a tad, just grab the belt pulley and give 'er a grunt.



[Log in to Reply]  [No Email]
Bob

05-10-2008 08:52:13




Report to Moderator
 Re: 1950 B Starter Question in reply to elcajonfarms, 05-10-2008 08:43:08  
Did you try (safely) rotating the flywheel a bit, perhaps aligning the gears better so the starter drive pinion can better engage the ring gear?

That MAY help, and after a few starts things will get polished up again, so the gears engage easier.

(It sounds to me like the teeth are not engaging, then the lever doesn't move far enough to make contact and power up the starter.)



[Log in to Reply]  [No Email]
elcajonfarms

05-18-2008 21:01:48




Report to Moderator
 Re: 1950 B Starter Question in reply to Bob, 05-10-2008 08:52:13  
I finally figured out my "starter" problem. The starter works fine, it's the tractor that's the problem. After getting a clutch-head driver at Napa so I could remove the flywheel cover, I discovered that rocking the tractor did not move the flywheel at all--i.e., the engine is stuck {!!) after the tractor sat out in the elements for 3 years without running. So now I have a $1000 Iowa tractor that cost $1110 to move out here to California plus a $500 carburetor overhaul that is ruined too, all from too little time and too little attention paid to the small things. Any ideas on how to get this broken free? Three years doesn't seem like such a long time, does it??

[Log in to Reply]  [No Email]
elcajonfarms

05-10-2008 10:54:26




Report to Moderator
 Re: 1950 B Starter Question in reply to Bob, 05-10-2008 08:52:13  
This B has a fully-enclosed flywheel with no access panel, so it is not possible to turn the flywheel by hand (a serious defect in the later styled B's, if you ask me). I have tried rocking the tractor in gear by hand; maybe I should pull it out of position a bit and try again. I'll try the WD-40 first, though.



[Log in to Reply]  [No Email]
55 50 Ron

05-10-2008 13:24:45




Report to Moderator
 Re: 1950 B Starter Question in reply to elcajonfarms, 05-10-2008 10:54:26  
I have rolled the engine on my 50 by hand by making sure the transmission is in neutral and the ignition is off, then engage the clutch and slightly roll the pulley. That's all that is usually necessary to have the starter and ring gear engage again if they were not previously.



[Log in to Reply]  [No Email]
RobMD

05-10-2008 11:04:28




Report to Moderator
 Defect?? in reply to elcajonfarms, 05-10-2008 10:54:26  
Uhm... what defect????

Seriously, all it takes to remove the flywheel COVER is about six quarter inch bolts and the removal of the starter foot pedal.

Very easy...

and Certainly not a defect.



[Log in to Reply]  [No Email]
elcajonfarms

05-10-2008 12:56:12




Report to Moderator
 Re: Defect?? in reply to RobMD, 05-10-2008 11:04:28  
I didn't mean to start an argument. I was just comparing some of the earlier electric start B's that had an access panel on the flywheel cover and a detachable steering wheel you could use to hand-start in an emergency. I agree it's safer to have a covered flywheel, and that the cover is easy enough to take off, but what I miss is the ease of hand-cranking!



[Log in to Reply]  [No Email]
Mike M

05-10-2008 13:03:02




Report to Moderator
 Re: Defect?? in reply to elcajonfarms, 05-10-2008 12:56:12  
Your 50' model B SHOULD have an access panel to pop out of the middle then you can use an adapter and a steering wheel to turn it over.

Very likely your switch contacts are worn. You may be able to adjust the starter push rod ( it is made to adjust ) and maybe bend the tang that pushes the switch so it makes contact again.



[Log in to Reply]  [No Email]
F-I-T

05-10-2008 19:25:51




Report to Moderator
 Re: Defect?? in reply to Mike M, 05-10-2008 13:03:02  
Yeah, I can't understand what he's saying here. Even the parts book shows ALL "B"s from 201,000 and up that had the full flywheel cover used the pop out center. Perhaps the defect is that he can't see the center cover is separate?



[Log in to Reply]  [No Email]
Bob

05-10-2008 11:37:58




Report to Moderator
 Re: Defect?? in reply to RobMD, 05-10-2008 11:04:28  
It's sure no DEFECT when it keeps blems from hand-cranking the starter-equipped engines by grabbing the flywheel, and getting torn apart by the ring gear!



[Log in to Reply]  [No Email]
Den N Ms

05-10-2008 13:42:55




Report to Moderator
 Re: Defect?? in reply to Bob, 05-10-2008 11:37:58  
Bob,I once saw a man at a tractor pull in Marshall Ill loose all four fingers on a hand.They had the flywheel cover off.He was tryin to start it up on the back of a truck.He had his brother step on the starter while he was gona pull it through.He grabbed that flywheel and pulled on it before I could stop him.Ran his hand between the flywheel ring gear and the engaged starter drive.He lost all four.

[Log in to Reply]  [No Email]
Bob

05-10-2008 14:46:21




Report to Moderator
 Re: Defect?? in reply to Den N Ms, 05-10-2008 13:42:55  
DAMN!



[Log in to Reply]  [No Email]
RobMD

05-10-2008 12:18:27




Report to Moderator
 speaking of which... in reply to Bob, 05-10-2008 11:37:58  
Bob, One time I was trying to free up a stuck 530 LP, and when it got to the point of being loose enough to rool back and forth by hands with moderate effort, I mangaged to skin all four knuckles near the starter area as it suddenly went all the way around.



[Log in to Reply]  [No Email]
Wilamayb

05-10-2008 21:52:19




Report to Moderator
 Re: speaking of which... in reply to RobMD, 05-10-2008 12:18:27  
You forgot to let go somewhere between 12 oclock and 6 oclok LOL!



[Log in to Reply]  [No Email]
RobMD

05-10-2008 22:16:26




Report to Moderator
 Re: speaking of which... in reply to Wilamayb, 05-10-2008 21:52:19  
Oh yeah, just kept on pushing, it was getting freer, and I was getting happier...

Happiness suddenly turned into a raging, hopping fit in which the entire village could hear my curses.



[Log in to Reply]  [No Email]
Bob

05-10-2008 12:50:05




Report to Moderator
 Re: speaking of which... in reply to RobMD, 05-10-2008 12:18:27  
YIKES!!!



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy