Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

420 PTO won't stop

Welcome Guest, Log in or Register
Author 
Mike Karney

04-16-2008 18:39:49




Report to Moderator

Anyone ever have this problem? I have a nice old 420-W, good strong runner, everything functions well. Its got the continuous running PTO and literally runs continuously! I can't stop the PTO while it is engaged, no matter how hard I press on the clutch. When I engage the PTO even with the clutch pressed down it grinds the gears as I engage the lever. I tried adjusting the free travel on the clutch pedal as the Service Manual explained but it made no difference. Anyone have any ideas? I'm really hoping that I won't have to split the tractor.

[Log in to Reply]   [No Email]
Dave H

04-17-2008 05:03:23




Report to Moderator
 Re: 420 PTO won't stop in reply to Mike Karney, 04-16-2008 18:39:49  
Have you had the tractor a long time and the pto dlutch worked way back when? If so i bet Ray may have the answer.

I bought one like that one time, you know just a resl nice ole ractor. That two stage clutch turned out to be a spicer (I think) that has a separate disk for the pto part. Mine had a brand new disk in it from way back when that was never adjusted properly when installed.

If the pto portion of the clutch is not adjusted properly when set up, It basically will not matter how you adjust the drive clutch - the pto one stays out of adjustment.

Yeah I been there, aspparently someone used a big boot to push mine in without the clutch. the lever had been welded on the shifter rod, the rod was bent and the engagement dog was toast in the trans.

good luck, and I hope she is just stuck.

If doing super light pto work, you can turn the motor off, put the pto in gear, and then start the trctor. That should make someone ask, "how come you don't just put the clutch in and shift the pto in?"

[Log in to Reply]  [No Email]
Ray

04-16-2008 19:20:26




Report to Moderator
 Re: 420 PTO won't stop in reply to Mike Karney, 04-16-2008 18:39:49  
The pto clutch disc isn't releasing.Has the tractor set for a long time,sometimes they stick but will usually free up when hooked to something.The clutch disc could be bad,or you could have a broken bolt in the clutch assembly that binds the clutch.



[Log in to Reply]  [No Email]
Mike Karney

04-17-2008 18:11:59




Report to Moderator
 Re: 420 PTO won't stop in reply to Ray, 04-16-2008 19:20:26  
Fellas:

I bought the tractor a little over a year ago and it was just being used for light chores (no PTO work). I found out right away that the PTO was sticking on. When I turn the PTO control lever off, the PTO does still spin a little, but if I push on it with a stick or something, it stops with little effort. I have used a brush hog a handful of times already, hoping it would break loose. But nothing so far. Thanks for the input, and if anyone else knows an easy way to take care of this, please feel free to chime in!

Thanks again,

Mike

[Log in to Reply]  [No Email]
58-420W

04-19-2008 01:59:31




Report to Moderator
 Re: 420 PTO won't stop in reply to Mike Karney, 04-17-2008 18:11:59  
Mike, If I'm understanding you correctly, you disengage the pto with the lever down between the seat and the shifter assembly and then you can take a stick or other object and stop the pto shaft from spinning with very little pressure applied. This is exactly what my 420W does and we have always considered it normal, since it won't turn when anything is hooked up to it. Then of course when the pto lever is engaged and the clutch is released it operates whatever implement you have attached correctly. I don't think your clutch is sticking, because if it was you would hear alot of gear grinding when trying to engage the pto with the lever below the front of your seat. At least that was the symptoms mine had when one part of the clutch started sticking. My tractor drove fine, but when I tried to engage the pto I had to slow the idle way down and grind it in. If you must, there is a clutch/pedal travel adjustment procedure you might try. It's either in the operator or service manual and if memory serves me correctly you don't have to split your tractor apart to perform it. I'm thinking there is some sort of adjustment straight below the battery. That being said, I still think your tractor is working correctly if you push on your clutch and the brush hog stops, you release your clutch and the brush hog starts, and most importantly, you don't have any grinding while engaging or disengaging your pto lever. Hope this helps. 58-420W

[Log in to Reply]  [No Email]
Mike Karney

04-25-2008 03:28:20




Report to Moderator
 Re: 420 PTO won't stop in reply to 58-420W, 04-19-2008 01:59:31  
58-420W:

I've got the operation of the PTO control lever down. Unfortunately, the PTO does not stop when engaged and when I push the clutch in. Even with the brush hog attached, it just keeps running at full speed. So to engage the PTO I either have to grind it or shut the tractor off, engage the PTO, and then start back up and start mowing. I have tried the only adjust that the service manual gives (the clutch free travel adjustment) but it made no difference at all. I guess for now, i'm just going to limp along, but I don't want to damage anything, so eventually, its going to come apart.

[Log in to Reply]  [No Email]
58-420W

05-03-2008 12:35:53




Report to Moderator
 Re: 420 PTO won't stop in reply to Mike Karney, 04-25-2008 03:28:20  
Mike,
Sorry for the long time with no response. It sounds like you definitely need to split the tractor apart and see what is going on with that clutch assembly. As mentioned previously, those clutches can get a little sticky and basically cause your pto to not disengage when your pressing on the clutch pedal. I would recommend getting this problem resolved as soon as possible, since you are using the pto with mowing. Grinding the pto into engagement is never good. I shelled out alot more money for some new gears due to the damage I caused from grinding the pto in. Best of luck on your repair. I hope it's something simple.

[Log in to Reply]  [No Email]
Dave H

04-18-2008 04:57:53




Report to Moderator
 Re: 420 PTO won't stop in reply to Mike Karney, 04-17-2008 18:11:59  
Well Mike, if it were mine I would say it is time to bust it in half. JMHO



[Log in to Reply]  [No Email]
lgc

04-16-2008 19:01:58




Report to Moderator
 Re: 420 PTO won't stop in reply to Mike Karney, 04-16-2008 18:39:49  
Are you sure its actually engaged? I have seen some of them spin the pto , especially when the oil is cold. But you could put your thumb in the end of it and stop it.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy