Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

2 cylinder wear

Welcome Guest, Log in or Register
Author 
moonlite 37

02-06-2008 14:05:36




Report to Moderator

When I was in High School, back in 2 cyl., days there was a myth (?) that a horizontal engine on a 2 cylinder would wear out of round by the weight of the pistons on the bottom side of the block. Those "experts" teenagers had most likely never seen one apart and certainly had never read a micrometer. I am sure many of you have measured several. Any comments? At that time I also joined in and help spread this information but was just quoting the "Experts"

[Log in to Reply]   [No Email]
jdemaris

02-07-2008 06:05:37




Report to Moderator
 Re: 2 cylinder wear in reply to moonlite 37, 02-06-2008 14:05:36  
Seems if that was true, Subaru cars wouldn't be lasting 300,000 miles. They have Boxer engines which are basically two horizontal two-cylinder engines fused together.

I was working on two cyinder Deeres when they were being used as real farm tractors - and we rebuilt just as many vertical 420s-430s-440s as horizontal As, Bs, Hs, 530s, 630s, etc. Not exactly a controlled scientific study, but we didn't notice any big difference.

On small engine lawn mowers - yes - what you are calling "horizontal" engines did wear out faster. To the converse though, the industry calls them "vertical", and the upright piston engines are "horizontal." That, because "vertical" refers to the crankshaft position.
They wore early for other reasons though not caused by the sideways position of the piston.

[Log in to Reply]  [No Email]
Geoff Mathews

02-07-2008 02:02:10




Report to Moderator
 Re: 2 cylinder wear in reply to moonlite 37, 02-06-2008 14:05:36  
Marshalls in The UK made a horizantal single cylinder diesel. Over the years variations in transmission layout meant that direction of engine rotation varied. This resulted on the early versions the thrust side being on the bottom of the cylinder, whilst on the later versions the thrust was on the top of the cylinder. I have seen examples of both, and the wear was more noticeable on the thrust side and was not related to the weight of the piston.

[Log in to Reply]  [No Email]
buickanddeere

02-06-2008 19:34:50




Report to Moderator
 Re: 2 cylinder wear in reply to moonlite 37, 02-06-2008 14:05:36  
A myth started and spread by jealous Binderoids.



[Log in to Reply]  [No Email]
WeirdDeere

02-06-2008 23:01:29




Report to Moderator
 Re: 2 cylinder wear in reply to buickanddeere, 02-06-2008 19:34:50  
B+D,

Something tells me you've been reading the ATIS list lately...Binderoids. Ahh, that's a good one.

Brandon



[Log in to Reply]  [No Email]
buickanddeere

02-08-2008 07:14:11




Report to Moderator
 Re: 2 cylinder wear in reply to WeirdDeere, 02-06-2008 23:01:29  
J.R.'s designation was too good not to pass on and use.



[Log in to Reply]  [No Email]
moonlite 37

02-06-2008 17:17:14




Report to Moderator
 Re: 2 cylinder wear in reply to moonlite 37, 02-06-2008 14:05:36  
Thank all you fellows. Back in 1950's in high school tractors were more important than girls but we knew very little about either.



[Log in to Reply]  [No Email]
Momsworry

02-06-2008 16:25:53




Report to Moderator
 Re: 2 cylinder wear in reply to moonlite 37, 02-06-2008 14:05:36  
I've heard this said about opposed aircraft engines as well, but have never seen or heard of any documented cases of it.



[Log in to Reply]  [No Email]
Hoss in Maine

02-06-2008 14:12:29




Report to Moderator
 Re: 2 cylinder wear in reply to moonlite 37, 02-06-2008 14:05:36  
Not so!For some unbenonst reason they wear the top side. Later Hoss



[Log in to Reply]  [No Email]
BLinWMi

02-06-2008 16:13:53




Report to Moderator
 Re: 2 cylinder wear in reply to Hoss in Maine, 02-06-2008 14:12:29  
Not always the case, I have seen a 35 B that a buddy of mine got into 15 years ago that actually was so worn that you could slide a dime under the piston on the bottom. It had worn itself egg shaped over the years. Luckily he only bought the tractor because it had a good set of spokes on it, which he put on a 35 B that had bad wheels but had so few hours, the original steering wheel still had the ribs in it.

[Log in to Reply]  [No Email]
Tom43

02-06-2008 15:24:09




Report to Moderator
 Re: 2 cylinder wear in reply to Hoss in Maine, 02-06-2008 14:12:29  
Good point. All engines wear more on the major thrust side of the piston. Some manufacturers used offset piston pins to counteract this



[Log in to Reply]  [No Email]
Tom43

02-06-2008 15:23:56




Report to Moderator
 Re: 2 cylinder wear in reply to Hoss in Maine, 02-06-2008 14:12:29  
Good point. All engines wear more on the major thrust side of the piston. Some manufacturers used offset piston pins to counteract this



[Log in to Reply]  [No Email]
Roger in Iowa

02-06-2008 14:31:02




Report to Moderator
 Re: 2 cylinder wear in reply to Hoss in Maine, 02-06-2008 14:12:29  
The wear on the topside may be caused by the forces during the power stroke. The rod is going around the bottom of the crank and the forces would be upward on the piston. That force would be greater than the gravity pulling down during exhaust and probably greater than gravity and force during compression.

my 2 cents.
Roger in Iowa



[Log in to Reply]  [No Email]
Skyhawk Greg

02-07-2008 08:23:44




Report to Moderator
 Re: 2 cylinder wear in reply to Roger in Iowa, 02-06-2008 14:31:02  
Roger -

Some of the old Oil Pulls had offset cranks to help with this, and to transmit the BMEP better.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy