Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

630 Head Is Off, Worth Putting In Hardened Valve Seats?

Welcome Guest, Log in or Register
Author 
GlenT

12-06-2007 08:04:21




Report to Moderator

I have my 630 head off while doing a engine rebuild/restoration and use the tractor for plowing lots of snow here in Minnesota, using the hydraulics for splitting wood, for logging firewood (lots of it), and discing a large garden and 2 acre field. So, it does work and also runs at 1125 RPM with little load (splitting wood).

Is it worth putting in hardened valve seats? Or maybe I should ask whether anyone has seen valve seat recession in a JD 2-cylinder tractor?

I have used a lead substitute since the change to unleaded but wonder if I need to.

Thanks in advance once again!

[Log in to Reply]   [No Email]
buickanddeere

12-09-2007 10:50:21




Report to Moderator
 Re: 630 Head Is Off, Worth Putting In Hardened Valve Seats? in reply to GlenT, 12-06-2007 08:04:21  
8.1 to 1 is pretty modest by some standards. You could certainly go higher but it's all you safely want with a good margin for error. With pump gas on a large bore low speed engine that doesn't use a quench combustion chamber design.
A freshly ground cam, a cylinder head bowl smoothing & port matching. And that 620 with pto HP up there with a 720 and not loose any fuel efficiency.



[Log in to Reply]  [No Email]
buickanddeere

12-06-2007 17:19:33




Report to Moderator
 Re: 630 Head Is Off, Worth Putting In Hardened Valve Seats? in reply to GlenT, 12-06-2007 08:04:21  
May as well install the hardened seats and not have that nagging worry in the back of your mind. While not as critical as in a diesel for starting. Sunk valves in a gasser cut power due to reduced compression and reduced airflow. There is a free hp or 2 or 3 or more with five angle valve seats, blending the rough edges out of the valve bowls and port to manifold matching. For all the tractor is used, even if it did ping on 87 octane. With high altitude or LP pistons. Purchasing 89,91 octane or mixing in 10-20% 100LL from the local airport isn't going to cost more than pocket change every year. The factory gasser pistons gave a wimpy 6.4 to 1 compression. The LP's are 8.1 to 1 .

[Log in to Reply]  [No Email]
GlenT

12-08-2007 13:42:07




Report to Moderator
 Re: 630 Head Is Off, Worth Putting In Hardened Valve Seats? in reply to buickanddeere, 12-06-2007 17:19:33  
You mentioned that the 'The factory gasser pistons gave a wimpy 6.4 to 1 compression. The LP's are 8.1 to 1'. If the LP and High Altitude pistons are not the same, do you know what the High Altitude piston gives a compression ratio of?

Do you have any idea what the octane rating of gas was back in the late 1950s?

Thanks for the post and good info.



[Log in to Reply]  [No Email]
J. Schwiebert.

12-06-2007 14:33:18




Report to Moderator
 Re: 630 Head Is Off, Worth Putting In Hardened Valve Seats? in reply to GlenT, 12-06-2007 08:04:21  
Well you are asking about two things here. Valve recession may be because the head has been off and the valves ground before. When I taught the machine shop classes we recommened the hardened seat. Remember hard seat and stellite seats for propane are two different issues.One of the last heads I worked on for a late A head and the recession was close to0.100! J.



[Log in to Reply]  [No Email]
Mike M

12-06-2007 19:05:21




Report to Moderator
 Re: 630 Head Is Off, Worth Putting In Hardened Valve Seats? in reply to J. Schwiebert., 12-06-2007 14:33:18  
Where did you find specs. for valve seat height on a JD A ? I would sure like to have a copy.



[Log in to Reply]  [No Email]
J. Schwiebert.

12-06-2007 19:18:38




Report to Moderator
 Re: 630 Head Is Off, Worth Putting In Hardened Valve Seats? in reply to Mike M, 12-06-2007 19:05:21  
I am on my son's computer tonight a couple of hours from home. Send me an e-mail address or a phone number.



[Log in to Reply]  [No Email]
Mike M

12-06-2007 19:24:51




Report to Moderator
 Re: 630 Head Is Off, Worth Putting In Hardened Valve Seats? in reply to J. Schwiebert., 12-06-2007 19:18:38  
Your email is not open ? I opened up mine send me a line and I can email back. Thanks



[Log in to Reply]  [No Email]
J. Schwiebert.

12-06-2007 14:57:08




Report to Moderator
 Re: 630 Head Is Off, Worth Putting In Hardened Valve Seats? in reply to J. Schwiebert., 12-06-2007 14:33:18  
I thought of this after my post but in the box of show and tell valves that we passed around in the machine shop class that showed failures we had a John Deere 620 or 630 valve that had a very severe case of "necking" in fact the stem diameter was down close to a 1/4 inch!. By all means check them !J.



[Log in to Reply]  [No Email]
machinery-man

12-06-2007 09:25:54




Report to Moderator
 Re: 630 Head Is Off, Worth Putting In Hardened Valve Seats? in reply to GlenT, 12-06-2007 08:04:21  
Glen T. I rebuilt a 620 and needed new pistons and installed the hi altiutude type..JD the dish was some smaller but wow what it did to that engine....just mentioning if you have to do pistons....



[Log in to Reply]  [No Email]
GlenT

12-06-2007 11:30:43




Report to Moderator
 Re: 630 Head Is Off, Worth Putting In Hardened Valve Seats? in reply to machinery-man, 12-06-2007 09:25:54  
Good idea on the pistons. Is there any problem with knocking, etc. using unleaded 87 octane gas with the high altitude pistons? Any idea what the compression ratio is with those pistons? I wonder what the typical gas octane was back in the late 1950s?



[Log in to Reply]  [No Email]
Mike M

12-06-2007 09:12:07




Report to Moderator
 Re: 630 Head Is Off, Worth Putting In Hardened Valve Seats? in reply to GlenT, 12-06-2007 08:04:21  
No need to install them unless you need to from your seats being bad ?

The original part number on the ex. valves (I think)was changed at some point to another number due to the originals being soft or something. You might take a look at your valves for part numbers and compare to the numbers in the book and make sure yours have been replaced with the later ones at some point. If not I would.

[Log in to Reply]  [No Email]
GlenT

12-06-2007 11:39:25




Report to Moderator
 Re: 630 Head Is Off, Worth Putting In Hardened Valve Seats? in reply to Mike M, 12-06-2007 09:12:07  
I see that the exh. valves in a 620 are P/N A5628R and the sub. is P/N R20246R and for a 630 they are the 620 sub. of P/N R20246R. I wonder if the ones in a 630 are what you are referring to?



[Log in to Reply]  [No Email]
Mike M

12-06-2007 11:54:17




Report to Moderator
 Re: 630 Head Is Off, Worth Putting In Hardened Valve Seats? in reply to GlenT, 12-06-2007 11:39:25  
Sounds like you should be ok. I'd look for that number R20246 on the valve though. I couldn't remember when they changed,but it was a 620 I was working on and it had the subbed ones in it. I asked the original owner about it and he kinda remembered having valve trouble right after they bought it but after it came back from the shop they never had anymore trouble with it. P.S. check your carb. screws as this one sucked one in and there isn't enough piston clearance in there so they get knocking in there. Older tractors like A's have enough room to spit them out.

You know since the head is off. I'd go ahead and pop out those pistons as with wear these models seem to develope broken piston rings. I'm thinking the ring side clearance gets excessive letting the thin rings twist and break. another 620 I had apart for a knock had ring pieces worked/wallered up past the pistons and got beat up to the cyl. head.

[Log in to Reply]  [No Email]
F-I-T

12-06-2007 09:02:03




Report to Moderator
 Re: 630 Head Is Off, Worth Putting In Hardened Valve Seats? in reply to GlenT, 12-06-2007 08:04:21  
Whenever I have seats replaced in a head these days (the last one I had done that way was my VAC Case), I opt for hardened seats, though with todays materials, that's about all you can buy. That said, unless you intend to pull the old girl hard and long as if working it as it was when it was a primary power tractor on the farm to the tune of 500 or more hours in a year, I doubt that you can hurt the original seats after a decent grind job. My two cents.

Frank

[Log in to Reply]  [No Email]
F-I-T

12-06-2007 09:02:01




Report to Moderator
 Re: 630 Head Is Off, Worth Putting In Hardened Valve Seats? in reply to GlenT, 12-06-2007 08:04:21  
Whenever I have seats replaced in a head these days (the last one I had done that way was my VAC Case), I opt for hardened seats, though with todays materials, that's about all you can buy. That said, unless you intend to pull the old girl hard and long as if working it as it was when it was a primary power tractor on the farm to the tune of 500 or more hours in a year, I doubt that you can hurt the original seats after a decent grind job. My two cents.

Frank

[Log in to Reply]  [No Email]
machinery-man

12-06-2007 08:39:41




Report to Moderator
 Re: 630 Head Is Off, Worth Putting In Hardened Valve Seats? in reply to GlenT, 12-06-2007 08:04:21  
As far a I know LP heads were the only ones with Hardened seats. If anything I would surmise seats could be a problem unless installed accurately. I've never heard of the need.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy