Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

820 problems/questions

Welcome Guest, Log in or Register
Author 
toolz

11-24-2007 19:01:24




Report to Moderator

Been wanting an 820/830 for some time. I bought an 820 green dash today at an auction. It has some good things- very straight, decent tires, electric start (I know- decreases value, but I like it), and it runs great. It was also very affordable.

The left rear wheel bearing appears to be bad- I can see the axle sitting higher in the housing. How much trouble is that? Will the axle be shot? Also, it"s pushing oil out the dipstick and flywheel housing. I went waaay back in the forum archives and found that the crank vent was up through the pony via a tube. I think I found the tube, and it"s got a cork in it, so hopefully that is the problem. It runs real good, so I hope it doesn"t need an overhaul, but if it does, it does.

Now for the dumb questions. I have never operated an 820. What is the lever next to the clutch lever? It"s not hooked to anything. Also, what are the two levers on the left? One of them is hooked to a rod that runs forward, and the other does nothing. One more- what is the 2-3" t-valve/lever just ahead of the top of the flywheel housing?

Never owned a two cylinder before, so I really appreciate your help. Kevin

[Log in to Reply]   [No Email]
Kent Petersen

11-25-2007 17:17:10




Report to Moderator
 Re: 820 problems/questions in reply to toolz, 11-24-2007 19:01:24  
Kevin get into a 830es manual and look at the crank case breather you need the oil bath air cleaner to hook up for the vaper pipe the 2 cyl diesels draw air into the crank case thru it Kent



[Log in to Reply]  [No Email]
Kent Petersen

11-25-2007 17:15:35




Report to Moderator
 Re: 820 problems/questions in reply to toolz, 11-24-2007 19:01:24  
Kevin get into a 830 manual and look at the crank case breather you need the oil bath air cleaner to hook up for the vaper pipe the 2 cyl diesels deaw air into the crank case thru it Kent



[Log in to Reply]  [No Email]
toolz

11-25-2007 20:19:26




Report to Moderator
 Re: 820 problems/questions in reply to Kent Petersen, 11-25-2007 17:15:35  
Thanks, Kent- I will do that. I appreciate your help. Kevin



[Log in to Reply]  [No Email]
toolz

11-25-2007 16:05:29




Report to Moderator
 Re: 820 problems/questions in reply to toolz, 11-24-2007 19:01:24  
2cyl- I read about your problems in the archives- I sure hope I don't run into that. It appears that the bearing can be pressed off towards the inside of the axle without removing the hub. If my axle is good, it sure would be nice to avoid what happened to you. How is the axle retained, and what does it take to get it out? Thanks a lot for the pictures. They explained a lot. I appreciate everybody's help. Kevin

[Log in to Reply]  [No Email]
2cylinderlp

11-25-2007 18:27:35




Report to Moderator
 Re: 820 problems/questions in reply to toolz, 11-25-2007 16:05:29  
third party image

I did say incorrectly that you would have to pull the cast wheels off. Although more awkward, you can probably pull the axle with the hub on it all as one piece like they did my replacements. It would be nice to have the hubs freed up though. I believe that you are correct in your assumption that the the bearing would slide off to the inside. Looking at a parts manual I see there is a shoulder on the axle that the inner race buts up against. On the other side of that shoulder (the outside) is a retainer for the felt seal that fits tight on the axle, then the felt seal, and then the outer felt retainer that presses into the axle housing. So it looks like to change the bearing, the whole business has to come out. The axle is retained just like other JD tractors, with a big nut that is on the inside of the bull gear. This picture is actually of a 730. But it would be very similar.

[Log in to Reply]  [No Email]
toolz

11-25-2007 20:16:19




Report to Moderator
 Re: 820 problems/questions in reply to 2cylinderlp, 11-25-2007 18:27:35  
2cyl- your pics are awesome! That answers my question perfectly. The inner axle nut would also set the axle endplay, since it would pull the outer bearing against it's race.

My 820 has the huge inner weights on it, so I will use my forklift to slide the whole assembly out, and replace the seal and bearing. As long as I'm carefull, it should be pretty easy. I should probably change the trans lube anyway, so all is good. Thanks again- Kevin

[Log in to Reply]  [No Email]
2cylinderlp

11-25-2007 08:48:51




Report to Moderator
 Re: 820 problems/questions in reply to toolz, 11-24-2007 19:01:24  
third party image

If the bearing is as bad as it sounds, you should be able to confirm that by just jacking the tractor up and watching to see if the axle drops in the housing. If you need to change the bearing, you will need to get the center cast wheel hub off and I'll describe how I did mine recently. Getting the hub off can be a challenge as I recently found out on my 830. The rear cast wheels were cracked and I was unaware of the problem at the time of purchase. The cracks were well hidden by wheel weights and the previous owner didn't disclose the issue. The method John Deere describes in the manual to remove the cast hubs is to simply use a 2 jaw puller. I have a nice OTC 2 jaw puller just like they show in the manual. But I can tell you that it was no where near up to the task. I ended up getting an Enerpac hydraulic porta-power setup witha 50 ton cylinder that has about a 2 inch stroke. That worked, but I used up just about all 50 tons worth of force. Because my hubs were cracked right through the openings where the puller would hook in, I drilled and tapped holes in the casting. My hubs were junk anyway, and it allowed me to narrow up the set up. As I applied force to the axle it just kept building and building, then BANG! The whole tractor shook and the hub moved about 1/16 of an inch. So I pumped it up again until just like the first time, there was the sudden slight movement and release of pressure. That process had to repeat about 10 more times before the axle/hub was really freed up. The salvage yard where I got my replacement hubs did not try to remove the axles because they said they didn't have a big enough press. I intend to try to get them out. If I can remove them, then I will have a couple extra axles. The spline is machined only about 4 inches in from each end in the hub. So the center of the hub is open all the way around with no splines. About a month before removal, I drilled a small hole on the back side of the hub to allow filling that cavity with penetrating oil. I used a 1/16 pipe plug to seal it.

[Log in to Reply]  [No Email]
2cylinderlp

11-25-2007 09:01:28




Report to Moderator
 Re: 820 problems/questions in reply to 2cylinderlp, 11-25-2007 08:48:51  
third party image

Here is my one of my replacement axle/hubs with the bearing. I could just clean this up and put it in. But I would much prefer to disassemble it. I am going to try to soak it from the inside like I did the other, and then with this one I'll probably heat it some. I am concerned also about just how to grab the hub. I am wondering if the original openings are strong enough for the higher forces that the hydraulic set up can produce?

[Log in to Reply]  [No Email]
MSM

11-25-2007 04:41:04




Report to Moderator
 Re: 820 problems/questions in reply to toolz, 11-24-2007 19:01:24  
The lever next to the clutch lever is the PT0. The 2 levers on the left were (1)for the engagement of the pony motor clutch and to engage the drive into the flywheel,and (2) a decompression lever.The T shaped handle disengages the gearing for the hydraulic pump,tractor must be shut off to engage this.



[Log in to Reply]  [No Email]
toolz

11-24-2007 21:16:26




Report to Moderator
 Re: 820 problems/questions in reply to toolz, 11-24-2007 19:01:24  
Just checked the serial number- 8204560, which should make it a black dash. It's been repainted, and the dash is green. Looks like I got a better deal than I thought.



[Log in to Reply]  [No Email]
WeirdDeere

11-25-2007 01:33:33




Report to Moderator
 Re: 820 problems/questions in reply to toolz, 11-24-2007 21:16:26  
You should buy SM2021, the official JD service manual for the green dash 820. It covers nearly everything except for the powersteering and hydraulics.

A VERY good manual!

I think your other questions were covered pretty well.

Brandon



[Log in to Reply]  [No Email]
toolz

11-24-2007 20:03:46




Report to Moderator
 Re: 820 problems/questions in reply to toolz, 11-24-2007 19:01:24  
Thanks, Bill- I will get the manuals, but just need a little advise till then. I appreciate your help. Kevin



[Log in to Reply]  [No Email]
Bill-NNY

11-24-2007 19:39:56




Report to Moderator
 Re: 820 problems/questions in reply to toolz, 11-24-2007 19:01:24  
Kevin,
I would suggest that you find an owners manual on Ebay or order a new one from Deere. Parts and repair books are also available, and very helpful. Your Questions,,,, The lever next to the clutch sounds like the PTO lever, the two left side levers would be the starting levers for the pony engine start. One lever for compression release and the other to engage the pony. The "t- lever" sounds like the hydraulic pump "on-off" lever. it should have "on" and "off" embossed on the lever.
Enjoy your tractor , Bill

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy