Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

'48 B Questions

Welcome Guest, Log in or Register
Author 
C DC

11-01-2007 17:35:08




Report to Moderator

Please help me define the following markings and numbers;
On the bottom of the engine:
1. cast "B2500?" (cant read the last number)
2. cast "44"
3. a screwed on plate with "18x" or "x81" depending on which way is up.
On the bottom of the carburetor, there is "DLT-13" The data book says it should be a DLTX-67.
Any thoughts on that?

Last, did the roll-o-matic ever become standard? My B does not have it.
If it helps, the s/n starts with 215.

Thanks again for your help.

[Log in to Reply]   [No Email]
Mike M

11-02-2007 07:26:42




Report to Moderator
 Re: '48 B Questions in reply to C DC, 11-01-2007 17:35:08  
I see down below that you have ordered some manuals. I hope you are getting the factory JD parts book and service manual for that tractor as they are very detailed and complete. A MUST have ! Also there is a seperate book that covers the hyd. power-trol that you may want to get too. I don't have mine handy but can get numbers later if needed.



[Log in to Reply]  [No Email]
C DC

11-02-2007 08:31:06




Report to Moderator
 Re: '48 B Questions in reply to Mike M, 11-02-2007 07:26:42  
I have an operators manual I ordered off Ebay coming. I have not ordered a shop manual yet, although I did buy the "John Deere data book" and two other books on rebuilding/restoring twin cylinder Deere"s.
What would be the part number for a real JD parts and shop manual for a 215 s/n B? Where could I get them?
Thanks!



[Log in to Reply]  [No Email]
P Browning

11-02-2007 11:28:31




Report to Moderator
 Re: '48 B Questions in reply to C DC, 11-02-2007 08:31:06  
When you ask a question on this forum and do not list your email -- you make it hard to get a quick answer!

But I will try! Go to the JD-H Restoration site (below). Once there, scan across to ARTICLES 1, and the from the drop-downs, select DEERE PUBS. Page 2 tells you which Deere Publications remain available for your tractor, and page 1 tells you how to obtain them.

One of the publications -- a dandy by all standards, is the SM2004 Service Manual for which Deere will want roughly $100. Go to a site called retiredtractors.com (preceded by the traditional (www), and you should be able to find that very manual for half the going rate.

As for websites, you also need to get tuned in to the Deere Parts site (jdparts.deere.com). Signing up for an account here gives you vast investigative prowess.

While you are at the JD-H site, take a close look at the Item of Interest # 1 EXCERPT to see if this is a book you think you need. (PatB)

[Log in to Reply]  [No Email]
Mike M

11-02-2007 16:04:04




Report to Moderator
 Re: '48 B Questions in reply to P Browning, 11-02-2007 11:28:31  
Pat; I like the prices in my old 1993 catalog for SM2004 only $33.30 LOL ! and I bet I was crying back then about that.



[Log in to Reply]  [No Email]
C DC

11-02-2007 13:05:11




Report to Moderator
 Re: '48 B Questions in reply to P Browning, 11-02-2007 11:28:31  
Thanks Pat. I will check out that stuff this evening.
And, I will include my email from now on! :>)



[Log in to Reply]  [No Email]
Mike M

11-02-2007 15:58:17




Report to Moderator
 Re: '48 B Questions in reply to C DC, 11-02-2007 13:05:11  
The service manual is SM2004 parts book is PC330 operators manual is OMR2006 and the hyd. one is SM2011 I have an old ph # of 1-800-522-7448 this may still be it.



[Log in to Reply]  [No Email]
P Browning

11-02-2007 16:25:10




Report to Moderator
 Re: '48 B Questions in reply to Mike M, 11-02-2007 15:58:17  
Mike -- You are right! (800) 522-7448 is still the right telephone number for Deere Publications. Have three things at your finger tips when you call (1) Model letter or number, (2) Serial number, and (3) your credit card. Be advised that you may order hard copy, or on CD, and (of course) both ways. Ordering on CD may work out just great for those pubs you don't need very often -- and the shipping cost is less. (PatB)

[Log in to Reply]  [No Email]
Mike M

11-02-2007 09:33:17




Report to Moderator
 Re: '48 B Questions in reply to C DC, 11-02-2007 08:31:06  
I'll have to look them up and get back to you. Unless someone has that info handi and posts it. Some of those restoration books are not very good or accurate I've been told. There is an 800 number for Deere publications, you order right from Deere, it has been posted here alot. I don't have it handi either.



[Log in to Reply]  [No Email]
johns48jdb

11-02-2007 05:21:47




Report to Moderator
 Re: '48 B Questions in reply to C DC, 11-01-2007 17:35:08  
i hate to see tractors that are 6 volt butchered up to 12 v. its yours to do with, but if your going to show it put it back 6 v. you can't mix and 12 v stuff, except fot the starter and i think i've read where that will eventually ruin the starter.



[Log in to Reply]  [No Email]
C DC

11-02-2007 05:43:25




Report to Moderator
 Re: '48 B Questions in reply to johns48jdb, 11-02-2007 05:21:47  
That"s the direction I"m leaning towards John. Even if the 12v is functional, it just does not sit well with me knowing it should be a 6v system. Besides, the automotive type alternator on there now is just plain ugly. Doesn"t fit with overall looks at all.



[Log in to Reply]  [No Email]
Mike M

11-01-2007 19:47:10




Report to Moderator
 Re: '48 B Questions in reply to C DC, 11-01-2007 17:35:08  
B2500 last should be an R would be the block casting part number. The rest doesn't mean anything really. DLT-13 is casting part number of the bowl only. Look at the side of the carb. body up front by the choke on the right hand side should have DLTX then number stamped in.Hopefully 67 Roll-o-matic was an option along with several other front end styles.



[Log in to Reply]  [No Email]
C DC

11-02-2007 04:03:06




Report to Moderator
 Re: '48 B Questions in reply to Mike M, 11-01-2007 19:47:10  
Thanks Mike, I"ll check the carburetor"s number today.
So much to learn!
As far as my starting issue goes, I jumped it with my pick-up last night and it turned right over and started ok. I had to leave the truck connected for a while because when it first started and I disconnected the jumpers, the B just died. After it had been running a while, it was fine with the truck disconnected. With the truck off, I measured the voltage at the battery. It was 11.4 at first and later 12.6. So, it has a 12v alternator and an apparently bad 6v battery - and thats where the problem is.
Now, should I leave it 12v or should I restore the original 6v system?
By the way, I think it still has the 6v starter because with a healthy 12v battery on it, it turns over really fast.

[Log in to Reply]  [No Email]
Mike M

11-02-2007 07:18:34




Report to Moderator
 Re: '48 B Questions in reply to C DC, 11-02-2007 04:03:06  
If you are running a magneto you can get problems with a 12 volt conversion spinning them too fast that the impulse coupling doesn't retard the timing for starting. I stick to leaving them original 6 volt as they were made. If I want a 12 volt I get a newer model tractor. The main weak link I have found with 6 volt is the batteries are not made very good anymore and don't last. I have not yet tried the Optima sealed gel ones yet,but they sound like they might be the ticket.

[Log in to Reply]  [No Email]
THE SMOOTHED DEERES

11-01-2007 20:01:47




Report to Moderator
 Re: '48 B Questions in reply to Mike M, 11-01-2007 19:47:10  
Hey mike got a question for u . My throttle lever has alot of play in it. The hole in the shaft where the screw sets is no longer a circle but well rounded out looking more now like an oval shape. Any tips or remedies for fixing this with tractor assembled? I think i could get it ,maybe just some gorrilla glue down in the hole and tighten the screw in but that means it may never come apart again ..? thks mike

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy