Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

6030 john deere backfire or popping

Welcome Guest, Log in or Register
Author 
francis pawelek

07-20-2007 19:51:01




Report to Moderator

i recently overhauled my engine,during this time,i had the head reworked too,after setting the timing,from tdc,well the center of the square cutout anyway cause i could find no line to start with,then i set the crank,cam,and injector pump all together,evrything at a perfect setting,gapped the exhaust valves at.028,and the intake at .018,now the motor is running and theres popping at certain mid range accelerations,at full throttle theres good black smoke,and sounds pretty good,i pulled the injectors and had all them rebuit,installed them,bled the pump,and lines to the injectors and the sound is back ,does anyone know where i went wrong?also where is the actual timing line located at the window?is it in the center?or top or bottom of the window under the cab on right side below,thanks

[Log in to Reply]   [No Email]
francis pawelek

07-22-2007 19:23:30




Report to Moderator
 Re: 6030 john deere backfire or popping in reply to francis pawelek, 07-20-2007 19:51:01  
guys thanks for your help,the fuel pump had to be retarded 1 line back,cleared out then ran great,now whats the best way to get the alternator to charge?untie the wires and cross them?i may have the 2 crossed coming out of the alternator,



[Log in to Reply]  [No Email]
donmyeil

07-21-2007 06:15:02




Report to Moderator
 Re: 6030 john deere backfire or popping in reply to francis pawelek, 07-20-2007 19:51:01  
You better go back and look at the timing window on the clutch housing. theres a mark there and not necessarly in the middle. I assume the camshaft marks were lined up with the crank. At that time you should be able to see the flywheel to clutch hsng. marks. sounds like its way out of time to me. abt. 1/4 inch on the flywheel is abt 2 degrees. also check the speed advance on the inj. pump for correct advance. hope this helps.

[Log in to Reply]  [No Email]
donmyeuil

07-22-2007 08:20:16




Report to Moderator
 Re: 6030 john deere backfire or popping in reply to donmyeil, 07-21-2007 06:15:02  
Hey , I need to correct this. The non turboed 6030 used the roosa-master pump which I was thinking. For turboed engines they used the in-line pump. To time that use the inj mark on the "crank pulley" there is a pointer on the cover. . sorry abt that.



[Log in to Reply]  [No Email]
francis pawelek

07-21-2007 21:19:17




Report to Moderator
 Re: 6030 john deere backfire or popping in reply to donmyeil, 07-21-2007 06:15:02  
hey donnie,would i have to move my flywheel clockwise about 1/4 inch then by resetting the fuel pump only,,would that help?man i sure dont feel like pulling that front timing cover off the block again,its a lotta time there,,to me it seems that the fuel pump gear is the easiest route,,8 or so bolts,undo the gear and restab it,,but make sure the lines are together on the fuel pump,what u think sir?

[Log in to Reply]  [No Email]
francis pawelek

07-21-2007 15:31:34




Report to Moderator
 Re: 6030 john deere backfire or popping in reply to donmyeil, 07-21-2007 06:15:02  
ok so what if i advanced the fuel pump,,,seriously i cant find nothing but tdc and a line but nowhere to line it up with sir,,
now that speed advance which is it and where to i adjust it at?i"m only used to the 7020 fuel system and 8630,but never really had to mess with neither,can you call me later ,,,i"ll understand better,361-562-1720



[Log in to Reply]  [No Email]
buickanddeere

07-21-2007 03:10:47




Report to Moderator
 Re: 6030 john deere backfire or popping in reply to francis pawelek, 07-20-2007 19:51:01  
What does it show for HP on the dyno and hour?
Re-ringed or new pistons & sleeves? New valve guides, new valves and new seats or a re-grind job? What is the fuel pressure going into the injection pump? What was the engine's condition prior to rebuild?



[Log in to Reply]  [No Email]
francis pawelek

07-21-2007 15:39:22




Report to Moderator
 Re: 6030 john deere backfire or popping in reply to buickanddeere, 07-21-2007 03:10:47  
condition before,almost burnt up cause my buddy sheared all teeth off thew cam,leaving the oil pump no way to work but shut it down in time,motor has 8600 hours,has new rings,liners,pistons,mains,rod bearings all new gaskets,i'm getting oil in the oilpan now,my 7520 done that,had a bad pump shaft o ring,the umbrella types,
man i cant see no timing mark is why i set it in the center,crank,and cam,and injector pump are call timed perfect,but the flywheel mark is setin center of the window cause i cant find a mark,which would it be at?top of window,or lower part of window?all valves were reground,and recut in new seats,everything looks great,new seals,guides the works,and milled down too,cam is new too..dyno not sure yet,,,fuel pressure unsure but blows a very good stream out when i bleed the injectors,,,,francis 361-562-1720

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy