Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

3010 new clutch question - HELP!

Welcome Guest, Log in or Register
Author 
JB in NE

05-26-2007 19:34:04




Report to Moderator

I just finished up putting in a new clutch assembly in a 3010. All went together good. I slid the clutch adjustment all the way forward in the slot and the clutch does not engage. I have to adjust it 1/2 back in the slot to get the proper free play and then it engages way out at the end of the pedal. I cannot figure this out. Any Ideas?? Thanks




[Log in to Reply]   [No Email]
rexhellwig

05-26-2007 22:17:00




Report to Moderator
 Re: 3010 new clutch question - HELP! in reply to JB in NE, 05-26-2007 19:34:04  
Did you disturb the throwout bearing while it was split?

It's easy for the bearing/tube assy to come out of position and fail to reseat fully rearward. You can check and correct this from the lower inspection hole.



[Log in to Reply]  [No Email]
Bob

05-27-2007 09:20:55




Report to Moderator
 Re: 3010 new clutch question - HELP! in reply to rexhellwig, 05-26-2007 22:17:00  
Unless the something is really "cocked with the TO bearing and sleeve, it will finish seating the firat time the clutch is depressed.



[Log in to Reply]  [No Email]
JB in NE

05-27-2007 09:11:57




Report to Moderator
 Re: 3010 new clutch question - HELP! in reply to rexhellwig, 05-26-2007 22:17:00  
Yes, I did replace the bearings while I was in there. How can I check to make sure that the tube assemby is fully seated?



[Log in to Reply]  [No Email]
rexhellwig

05-27-2007 13:28:00




Report to Moderator
 Re: 3010 new clutch question - HELP! in reply to JB in NE, 05-27-2007 09:11:57  
Remove the lower inspection cover.
Direct your attention {and a good light} to the very back of the clutch housing.
You want to take a careful look at where the rear of the bearing tube enters into a doughnut sized/shaped collar. This collar has two pins that fit into the clutch pedal forks. When new, these parts are a light press fit. You want to make sure this collar is at a perfect right angle with the tube. If this joint appears slightly off center, align the collar with a long screwdriver while an assistant steps on the pedal when directed. This will usually supply enough force to press the parts back together. If this isn't seated, It causes symptoms just like you have described.

Now the bad news. If you're sure this is OK, You really need to split the tractor again and verify everything. Why? Because you really have narrowed it down to the finger adjustment that the dealer made. It's true you can "adjust" the trans clutch from below, but if your man at the dealership can't get these fingers right...There's no way he got the PTO levers right either...And there's no way you are going to adjust them without a split.

[Log in to Reply]  [No Email]
JB in NE

05-28-2007 07:51:57




Report to Moderator
 Re: 3010 new clutch question - HELP! in reply to rexhellwig, 05-27-2007 13:28:00  
Went out this morning and checked as Rex suggested and he wins! The collar that the tube assembly slides into was pointed downward and the tube wedged at an angle. Got the tube situated pushed the pedal and in it went and seated. Readjusted the pedal and all appears to be good. Hard to believe this was all it was but glad it was simple. Thanks to all of you for your help!!



[Log in to Reply]  [No Email]
rexhellwig

05-28-2007 12:58:52




Report to Moderator
 Re: 3010 new clutch question - HELP! in reply to JB in NE, 05-28-2007 07:51:57  
Since this is Memorial Day, I'll thank Myron Ellis, my old shop foreman, for showing me this trick over 25 years ago.

He fought in some of the Pacific islands battles in WW2.



[Log in to Reply]  [No Email]
msb

05-26-2007 19:39:05




Report to Moderator
 Re: 3010 new clutch question - HELP! in reply to JB in NE, 05-26-2007 19:34:04  
Clutch finger height is out of adjustment.I assume you set the fingers with a gauge?



[Log in to Reply]  [No Email]
JB in NE

05-26-2007 19:55:58




Report to Moderator
 Re: 3010 new clutch question - HELP! in reply to msb, 05-26-2007 19:39:05  
I took this to Deere and had them adjusted and the flywheel marked for me.



[Log in to Reply]  [No Email]
Bob

05-26-2007 21:19:20




Report to Moderator
 Re: 3010 new clutch question - HELP! in reply to JB in NE, 05-26-2007 19:55:58  
I also had the nearby DEERE dealer's shop set up a clutch... a 4020. It was a NEW flywheel. and mostly new clutch parts. The they assembled the clutch, then bolted it to the new flywheel, and set the fingers. I took it to may shop, carefully marked the flywheel and pressure plate, then installed them on the tractor, making SURE the marks were aligned.

They screwed it up beyond belief, then wouldn't warranty it when it failed.

So, DON'T rule out improperly set fingers as the problem, just yet.

Since then, I bought the adjustment gauge, set the fingers myself, and have never had a problem.

I don't know if they were just careless, or it was a young "wrench" who had never worked on anything that old before!

[Log in to Reply]  [No Email]
JB in NE

05-26-2007 21:30:19




Report to Moderator
 Re: 3010 new clutch question - HELP! in reply to Bob, 05-26-2007 21:19:20  
Sounds like two votes for clutch finger adjustment is wrong. I can't even imagine spliting this this again! Any other Ideas?



[Log in to Reply]  [No Email]
HTR

05-27-2007 05:32:44




Report to Moderator
 Re: 3010 new clutch question - HELP! in reply to JB in NE, 05-26-2007 21:30:19  
Set the pedal adjustment about 1/4 inch from the bottom of the slot, working under the tractor, set the fingers so they just touch the release bearing, then set the pedal adjustment in the slot.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy