Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

4010 tie rods...(still rebuilding the burnt 4010)

Welcome Guest, Log in or Register
Author 
TimS in Mo

05-16-2007 08:57:31




Report to Moderator

I got the new load shaft seals in with no problems except getting the old ones out was a pain, I ended up using a dremel tool with a cutting wheel and cold chisels to get them split to get them out.

So...I started on the front end, I pulled the front wheels, one outer bearing is bad, most likely pre-fire, no wonder that tire kept sliding in the mud/snow so much. Anyhow, I decided to spread the front tires out to the '4 hole' width, which with the front rims dished out gives a 7 foot width outside to outside on the tires I am using.

Anyhow, the adjustable tie rods seem to be just stuck solid, I can't get them to extend at all...

Any hints? I've tried pipe wrenches, heat, pipe wrenches, most everything I can think of.

I am thinking of just replacing them, the tie rod ends are shot anyhow.

[Log in to Reply]   [No Email]
TimS in Mo

05-16-2007 19:49:21




Report to Moderator
 Re: 4010 tie rods...(still rebuilding the burnt 40 in reply to TimS in Mo, 05-16-2007 08:57:31  
That's a great idea...I bet I've spent 3 or 4 hours already trying to get those darn things apart, and the ends on them are burnt anyhow, I'm not sure what I was thinking.

I'll just order some new ones and to heck with it.



[Log in to Reply]  [No Email]
Glen in TX

05-16-2007 19:29:52




Report to Moderator
 Re: 4010 tie rods...(still rebuilding the burnt 40 in reply to TimS in Mo, 05-16-2007 08:57:31  
Should be able to get the whole tie rod assembly with joints, boots, nuts, bolts for about $110 to $130 + freight each aftermarket. At least that's what I'd have to sell them for. Did you check parts on this site? Same tie rod assembly fits 2510 up to 4320 with 88" tread axle.



[Log in to Reply]  [No Email]
G/MAN

05-16-2007 13:29:11




Report to Moderator
 Re: 4010 tie rods...(still rebuilding the burnt 40 in reply to TimS in Mo, 05-16-2007 08:57:31  
Yes, you might be ahead to replace the tubes, although usually a fair amount of heat will get them freed up. However, you can chew them up pretty good getting them free, so if the tractor is supposed to be a "looker", you might end up doing some grinding when you're done. Depending on the tube part number, new ones from Deere run from $60.00+ to $140.00. You might be able to find them cheaper through A&I, etc. A little anti-sieze on the new ends will aid future disassembly.

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy