Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

Dyno testing at PTO -vs- Belt Pulley

Welcome Guest, Log in or Register
Author 
Dave in SV

02-08-2007 14:43:42




Report to Moderator

I have been told that there are two ways to dyno test my '49A... and that the belt pulley test might be a bit safer, since the PTO test may break PTO gears, etc.

I welcome anyone's weigh-in on this!




[Log in to Reply]   [No Email]
DSK

02-09-2007 14:05:43




Report to Moderator
 Re: Dyno testing at PTO -vs- Belt Pulley in reply to Dave in SV, 02-08-2007 14:43:42  
Anything can happen with the Waterloo 2-cyl. PTO, and they are not bulletproof by any means. I know of a 45 GM that broke the casting boss out of the bottom of the case while operating a grinder-mixer. I know of an instance also that a puller G blew the same casting at 91 HP turning at 540. It all depends how much abuse (lugging) the PTO in any particular tractor has seen. We could start a whole new topic on what the 2-cyl. PTO does to U-joints and other implement driveline components...for another day.

[Log in to Reply]  [No Email]
Mike M

02-08-2007 18:29:00




Report to Moderator
 Re: Dyno testing at PTO -vs- Belt Pulley in reply to Dave in SV, 02-08-2007 14:43:42  
I agree with those that say if you are stock or near you should be fine. One would really have to be radical before I'd deam the pto unsafe. I have done an A that was around 55 HP and all was good. The dyno is really nice to get everything adjusted to max. power. On stock tractors I have not noticed any problems with power loss through the pto verses rated HP if the engine is good they will make pulley rated HP on the pto and sometimes more.So I would trust the pto figures unless your dyno is off.

[Log in to Reply]  [No Email]
95CS

02-08-2007 18:12:45




Report to Moderator
 Re: Dyno testing at PTO -vs- Belt Pulley in reply to Dave in SV, 02-08-2007 14:43:42  
I agree, a PTO dyno won't hurt your "A" unless there's already something wrong in the PTO drivetrain. One thing you need to remember is that the horsepower ratings were originally calculated from the belt pulley, so with a PTO dyno, you're likely to see in the neighborhood of a 10 to 15 percent power loss vs measuring horsepower at the belt pulley, due to losses in the PTO geartrain, etc.



[Log in to Reply]  [No Email]
Dave in SV

02-10-2007 21:55:18




Report to Moderator
 Re: Dyno testing at PTO -vs- Belt Pulley in reply to 95CS, 02-08-2007 18:12:45  
The spec sheet I have says that the A has 34.1 at the drawbar and 38.0 at the PTO/Belt. Dare I ask what drawbar HP is?



[Log in to Reply]  [No Email]
deere dan

02-08-2007 18:07:30




Report to Moderator
 Re: Dyno testing at PTO -vs- Belt Pulley in reply to Dave in SV, 02-08-2007 14:43:42  
My experience would ask "do you feel lucky"? Many moons ago, I had a 14 T baler unhook from a 70d the pto stub caught the tractor drawbar, snubbed it 'right now' and did no dammage. Plugged a 60' pto silage blower on a late 90 over AR and tore the center out of flyweel, flange off f/w side main,and bent the crank. "Well do ya" ??



[Log in to Reply]  [No Email]
machinery-man

02-08-2007 17:03:04




Report to Moderator
 Re: Dyno testing at PTO -vs- Belt Pulley in reply to Dave in SV, 02-08-2007 14:43:42  
those drive gears in the A are as good or better than 100 h.p. tractors today.....who ever got the ideal that they would tear up...most of them have been beat and banged on bushogs and if anything tears up it would be the cluster gear in the transmission....but that is due to backlash jerking and clunking with a bushog....no a steady continuous load like a dyno....



[Log in to Reply]  [No Email]
Ken52M

02-08-2007 16:29:50




Report to Moderator
 Re: Dyno testing at PTO -vs- Belt Pulley in reply to Dave in SV, 02-08-2007 14:43:42  
This reminds me of a story. I grew up on a dairy farm in Cert. WI. We had a early 420 that was used a lot for belt work and later on, a short hopper NH blower to blow long cut, partially green hay into the barn. This hay was difficult to blow and tended to slug up in the blower. I know, some of you are thinking that you can't put green hay in the barn. This hay was put on a barn dryer. 10 HP fan to keep hay cool till it dried. Anyway all that slugging in the blower eventually took the PTO gears out of that 420. I think that my Dad converted that blower to belt drive to solve that problem. I have a lot of fond memories of farmin w/ those Deeres. KB

[Log in to Reply]  [No Email]
leon

02-09-2007 03:43:02




Report to Moderator
 Re: Dyno testing at PTO -vs- Belt Pulley in reply to Ken52M, 02-08-2007 16:29:50  
How would converting the from PTO to belt drive help on a 420?



[Log in to Reply]  [No Email]
F-I-T

02-08-2007 15:18:35




Report to Moderator
 Re: Dyno testing at PTO -vs- Belt Pulley in reply to Dave in SV, 02-08-2007 14:43:42  
As far as safer, there's nothing like an accident waiting to happen as a flopping, 50 year old belt ready to spit it's hinge driving a belt driven anything. Plus, where are you going to find a belt pulley equipped dyno? Unless you build a Prony brake or take it to a Baker Fan stand that others can swear by for load....

Your '49 "A" has plenty of PTO gear strength to hold back its earth shaking 40 or so hp. I dyno my 70D all the time. It will really warm it up, though, and de-humidify all the oils!

Breaking pto gears on a dyno....Who comes up with these pearls of wisdom?

[Log in to Reply]  [No Email]
Dave in SV

02-08-2007 16:15:46




Report to Moderator
 Re: Dyno testing at PTO -vs- Belt Pulley in reply to F-I-T, 02-08-2007 15:18:35  
I thought some of the same things you mentioned, Frank, but I have no experience to back up my hunches yet.

A local Two-Cylinder Club has a belt pulley dyno... they bring it to spring/summer shows in the area and let local owners to test their beloved tractors. When I heard that PTO dyno's tend to damage PTO gears, I fiured that I should stay clear of it.

If the PTO design can't handle the horsepower, then the PTO is under-engineered, right? If, however, PTO's become prone to damage (due to age and wear?), then I'm not so sure I want to take the gamble. I doubt I'll ever use the PTO, but I don't want another project to explain to my beloved wife!

Thanks for the words of wisdom, Frank.

[Log in to Reply]  [No Email]
Drew

02-08-2007 15:10:52




Report to Moderator
 Re: Dyno testing at PTO -vs- Belt Pulley in reply to Dave in SV, 02-08-2007 14:43:42  
Unless you have in excess of 90-100hp, you shouldnt have any problems dynoing off the PTO. If you break the PTO dynoing on a stock/near stock tractor, then you had problems before you even backed up to the dyno.



[Log in to Reply]  [No Email]
Dave in SV

02-08-2007 16:19:18




Report to Moderator
 Re: Dyno testing at PTO -vs- Belt Pulley in reply to Drew, 02-08-2007 15:10:52  
Makes sense, Drew. My A is stock... I'm just curious what it's making, and would like to find out before I do some engine work.

Frank's comments about belts whipping around makes me wonder about the smarts in dyno'ing off the belt pulley.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy