Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

4020 Safety switch?

Welcome Guest, Log in or Register
Author 
Steenhoek

01-24-2007 20:27:04




Report to Moderator

I just bought a 4020 today. Started it at his house drove it home and can't even get it to turn over now. Is there a safety switch that I don't know about. Me not know is very likly so if someone could run through how to start it that would be of help. Also any ideas on the fist thing to check on why it won't even turn the starter over.
thanks
chad




[Log in to Reply]   [No Email]
jd@antique acres

01-25-2007 13:24:33




Report to Moderator
 Re: 4020 Safety switch? in reply to Steenhoek, 01-24-2007 20:27:04  
Like it was mentioned before, if it is a power shift I would check the clutch safety switch. I have found that this usually the number one problem of no power to the starter. And then it is likely just a bad connection, seems like a trouble spot for a lot of dirt, grime, and corrosion



[Log in to Reply]  [No Email]
Steenhoek

01-25-2007 06:58:23




Report to Moderator
 Re: 4020 Safety switch? Success! in reply to Steenhoek, 01-24-2007 20:27:04  
Turns out that it has to do with the overide to kill switch on the throttle. I used it to shut it of but it must be sticking. thanks again for your help

chad



[Log in to Reply]  [No Email]
Bob

01-25-2007 07:25:29




Report to Moderator
 Re: 4020 Safety switch? Success! in reply to Steenhoek, 01-25-2007 06:58:23  
You'd better re-think that one... you said the STARTER wouldn't operate... there's NOTHING electrical involved with the throttle lever or it's knob that would prevent the STARTER from
being activated.

For your own safety, and the well-being of your tractor, you REALLY need an operator's manual.

Check ebay, or call Deere TechPubs @ 1-800-522-7448. The new manuals are a bit expensive, but better than "flying blind" with your "new" tractor.

[Log in to Reply]  [No Email]
steenhoek

01-25-2007 07:48:43




Report to Moderator
 Re: 4020 Safety switch? Success! in reply to Bob, 01-25-2007 07:25:29  
That is a good point, the throttle overide just shuts down the diesel, right? I am off to get a manual, another good point. When you are a kid running a 4020 everyday during the summer, it does not translate into knowing how one works! ha

thanks
chad



[Log in to Reply]  [No Email]
TimS in Mo

01-25-2007 06:54:51




Report to Moderator
 Re: 4020 Safety switch? in reply to Steenhoek, 01-24-2007 20:27:04  
On my 4010, the park safety switch is under the cowling right at the top of the shifter. I have had the wire come unplugged on mine when I have had the cowling off or been working on the top of the engine or hydraulics there.

That would be the first thing I check, pull the 2 bolts on each side of the cowling, pull the cowling off, look to make sure the little switch that gets depressed when the shifter is in park has the wires hooked to it. If you need to take an ohm meter and check that the switch changes resistance when the shifter is in parked ( I don't know if thats a normally open or normally closed switch, I'm sure Gerald or somebody will fill that in here. )

You may be able to just put a jumper wire between those two wires that hook to the switch and then start it if that switch has failed. A lot of dirt and chaff and mud dauber nests can get in there and gum that switch up to, it might just need cleaning or adjustment.

Or maybe on the 4020 that switch is in a different spot....but I know that's where it is on my 61 4010.

[Log in to Reply]  [No Email]
buickanddeere

01-25-2007 03:04:20




Report to Moderator
 Re: 4020 Safety switch? in reply to Steenhoek, 01-24-2007 20:27:04  
12 or 24V system? Is each battery charged? Do you have the trans lever firmly in the park position?



[Log in to Reply]  [No Email]
Glen in TX

01-24-2007 21:09:30




Report to Moderator
 Re: 4020 Safety switch? in reply to Steenhoek, 01-24-2007 20:27:04  
The neutral safety switch is pretty easy to check behind battery box by putting a jumper wire in the harness plug and then seeing if it starts. Do NOT leave it like that though and fix it right so someone doesn't get run over if it's left in gear! The switch can be bad or just need shimmed too. Otherwise may be a bad key switch, solenoid, bad batteries, cables, starter, brushes ? Just have to narrow it down till you find it.

[Log in to Reply]  [No Email]
Steenhoek

01-24-2007 21:35:50




Report to Moderator
 Re: 4020 Safety switch? in reply to Glen in TX, 01-24-2007 21:09:30  
I will try those things, and let you know.

Thanks
chad



[Log in to Reply]  [No Email]
johndeeregene

01-24-2007 20:34:05




Report to Moderator
 Re: 4020 Safety switch? in reply to Steenhoek, 01-24-2007 20:27:04  
there is a park safety switch on the right side of the transmission case.



[Log in to Reply]  [No Email]
Gerald J.

01-24-2007 20:32:52




Report to Moderator
 Re: 4020 Safety switch? in reply to Steenhoek, 01-24-2007 20:27:04  
Yes, there is a safety switch. On the synchrorange it has to be shifted to park, all the way left and all the way forward to allow the starter to crank. Keeps it from running over you when you start it standing on the ground.

The power shift surely has to be shifted to neutral also for starting

Gerald J.



[Log in to Reply]  [No Email]
Steenhoek

01-24-2007 20:46:47




Report to Moderator
 Re: 4020 Safety switch? in reply to Gerald J., 01-24-2007 20:32:52  
What is the power shift? And how do you put it in neutral? It is in park so that it is not it.
Thanks
chad



[Log in to Reply]  [No Email]
ET

01-25-2007 04:43:11




Report to Moderator
 Re: 4020 Safety switch? in reply to Steenhoek, 01-24-2007 20:46:47  
If its a power shift transmission you have to hold down the clutch pedal as well as have it in neutral. The are two safety switches on these.



[Log in to Reply]  [No Email]
dds-inc

01-24-2007 21:14:18




Report to Moderator
 Re: 4020 Safety switch? in reply to Steenhoek, 01-24-2007 20:46:47  
its just another type of transmission. Looks like you have synchro transmission. I don't know what's going on, but there might be a switch that's bad. Also check the starter solenoid.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy