Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

1951 B vent pump.

Welcome Guest, Log in or Register
Author 
JDK

01-21-2007 07:33:09




Report to Moderator

third party image

I have a little oil leak. Parts catalog PC-330, refer to page 24, key 33, gasket on the vent pump housing cover.

Problem is that I dont know if the vent housing should just slide out from the govenor. I had all the bolts off, tugged and jerked and bumped it with a wooden handle. Wouldnt come off. I put the bolts back in and left it leak. The service manual says 'Disconnect from govenor case'. Sounds simple, I dont want to start hammering. Once I get it apart I can then pull the gear off and get a new gasket installed, according to the manual.

Am I right in guessing that this assembly should just unbolt and 'slide' off the govenor? Any advice, tips, tricks before I go back into this?

Thanks, JDK.

[Log in to Reply]   [No Email]
johns48jdb

01-21-2007 13:13:01




Report to Moderator
 Re: 1951 B vent pump. in reply to JDK, 01-21-2007 07:33:09  
why not clean it up real good and try a little silicone sealer before you go to all that trouble.



[Log in to Reply]  [No Email]
F-I-T

01-21-2007 09:39:29




Report to Moderator
 Re: 1951 B vent pump. in reply to JDK, 01-21-2007 07:33:09  
In addition to what the others said, there is a lip on the casting of the fan pump that engages pretty positvely into the governor case. While it is not a thumb press fit, it has to be aligned so it can locate properlt. Once it has been together a while, it might be reluctant to come loose. I've had to rap more than a few with a lead hammer to shock them apart.

Frank



[Log in to Reply]  [No Email]
jd b puller

01-21-2007 07:47:56




Report to Moderator
 Re: 1951 B vent pump. in reply to JDK, 01-21-2007 07:33:09  
yuk. How much time do you have?

You need to either slide the governor back or the fan forward. More than likely, you"ll do both. But you can"t slide it forward far enough because the radiator is in the way. And the radiator probably won"t want to move (you"ll either round off the heads of the bolts that hold it in or just plain snap them off...). So you are left with the governor housing. When you do this, it"s not bad, you just have to make sure you line it up with the cam gear when you put it back together. yee haw.

[Log in to Reply]  [No Email]
JDK

01-21-2007 07:57:45




Report to Moderator
 Re: 1951 B vent pump. in reply to jd b puller, 01-21-2007 07:47:56  
I guess I should have added that I had replaced the manifold and had the fan shaft/govenor assembly off as a unit.

I just couldnt get the fan shaft separated from the govenor.

Thanks. JDK.



[Log in to Reply]  [No Email]
kurt_JDB

01-21-2007 08:45:49




Report to Moderator
 Re: 1951 B vent pump. in reply to JDK, 01-21-2007 07:57:45  
JDK,

The assembly will come apart after you remove these bolts. I have a '51 B that I rebuilt the governor and fanshaft on recently. I recall having to pry and knock it a little bit to get the fan shaft/governor apart. Work one side and then the other.

There is a specific setup procedure upon reassembly of the fanshaft and governor to insure that the backlash and heel of the gears is set properly. This procedure is outlined well in the service manual and involves using different thickness of gaskets for adjustment. If what you put back is the same thickness as what you replace, it should be OK. I used a micrometer to measure my gaskets when I took it apart, and used that as a starting point. I ended up having to make a couple of the gaskets as Deere no longer sells all the various thicknesses.

Kurt

[Log in to Reply]  [No Email]
WILYCOAT

01-23-2007 12:48:22




Report to Moderator
 Re: 1951 B vent pump. in reply to kurt_JDB, 01-21-2007 08:45:49  
DOES THE 51 B HAVE A SPACER ON THE FAN SHAFT? I HAVE AN A THAT HAS A SPACER ON THE FAN SHAFT P/N B2921R THE ONE I HAVE I BELIEVE IS WORE I CAN MAKE A NEW ONE IF I CAN FIND OUT WHAT THE CORRECT LENGTH SHOULD BE

RICH



[Log in to Reply]  [No Email]
Kurt_JDB

01-23-2007 14:08:51




Report to Moderator
 Re: 1951 B vent pump. in reply to WILYCOAT, 01-23-2007 12:48:22  
I looked in my B parts book, but that part number is not in the index. I do not have an A book so I cannot help you there.

Kurt



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy