Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

38 D oil presure + other questions

Welcome Guest, Log in or Register
Author 
Todd Osborne

01-17-2007 15:35:57




Report to Moderator

Hi I have a 1938 D I have been working on and thanks to you guys I now have it running (thumbs up!! to all who chipped in with advice on timing and carb settings).
Now it's it running I find there is NO oil pressure at the gauge so have shut her down. I removed the gauge and put low pressure air in the gauge and that's seems ok as the needle moves fine..... .So were do I search next to check if the oil pump is OK?...or can it be some thing else?

Also a few pointers on the best setting to start the engine would be welcome as I'm a little green on this point ( pun intended) & getting blisters rolling this old Deere over and over....
I have done this:
1 / gears in neutral
2 / both decompression cocks open
3 / throttle on about half
4 / choke on full
and it still take quite a few goes to get it to fire....some times one chug and stops and if I hold my tongue in the left side of my mouth and cross my toes it will some time fire up.
It has a rebuilt mag and is getting both gas and spark, carb set as follows Idle jet 3/4 to 1 turn out
load jet 3/4 to one turn out.... so if any one can put me straight & just what I'm doing wrong that would be great.
Thanks Todd In New Zealand

[Log in to Reply]   [No Email]

01-26-2007 10:25:29




Report to Moderator
 Re: 38 D oil presure + other questions in reply to Todd Osborne, 01-17-2007 15:35:57  
My Dad has a 36 "D" and we always prime the cylinders with some gasoline before starting. Some of the "D"s had the cup type petcocks to use for this. We don't. We just turn them so they point up and get an oil can from the hardware store, one with the straight metal spout that you push the bottom of to make oil come out. Fill it with gasoline and squirt some into the cylinders. Choke it and it should start almost right away.

[Log in to Reply]  [No Email]
Glen in TX

01-18-2007 11:36:48




Report to Moderator
 Re: 38 D oil presure + other questions in reply to Todd Osborne, 01-17-2007 15:35:57  
third party image

Todd, You idle needle needs to be open 1 to 1 3/4 turns or less on gasoline. I've had some Ds that ran better with idle needle open 2 turns or more.

On the oil yes be sure you have pressure before running it more. You can open petcocks and remove spark plugs to make engine easier to turn by hand and roll it over and should have a steady stream of oil come out the elbow with guage off. Get a good known numbered guage and check for 10 to 15 psi oil pressure. There is a set screw down inside crankcase on top of the oil filter body that will allow you to adjust oil pressure. Other oil lines can be taken loose or cracked open some to see you have oil flowing to all bearings and where other lines go to such as governor also.

If you didn't pull the oil pump strainer when changing oil to check for or clean out sludge in bottom of the crankcase do it NOW! You won't have any oil flow to pump or pressure if the inlet strainer screen is blocked with sludge. Yes the oil filter body can also be distorted if someone has tighten the filter too hard and will cause lower oil pressure from leaks around it too. New oil filter body can is not available new so will have to straighten the old one and maybe remove it to do so. The I&T shop manual covers that very well on how to remove and fix the filter body can and reinstall it.

[Log in to Reply]  [No Email]
WeirdDeere

01-18-2007 00:19:44




Report to Moderator
 Re: 38 D oil presure + other questions in reply to Todd Osborne, 01-17-2007 15:35:57  
Make sure you have oil pressure before running it!

You may want to try a different gauge, preferably one with numbers. They don't have much oil pressure, something like 15psi, so you will need a LOW gauge!

To start, here's what I do:

Out of gear, clutch lever back.

Turn gas on.

Open petcocks.

Half throttle or a little less.

Full choke.

Turn it over slowly until you feel resistance (one of the cylinders coming up on compression).

Turn it slowly till near the end of the compression stroke and just keep rolling it over top dead center, no need to go too fast, just keep it moving and it will probably fire.

Repeat as necessary!

When it begins shooting a good mist out of the petcocks, I open the choke and continue turning it over. Or if it pops and tries to run I open the choke.

You'll figure it out. Practice, practice, and MORE practice! Each tractor has it's own personality too. Trying to start our '28 D can be amazingly easy one time and frustrating the next.

If all else fails, get a chain and tractor!

Good luck!
Brandon

[Log in to Reply]  [No Email]
Paul from MI

01-17-2007 18:02:18




Report to Moderator
 Re: 38 D oil presure + other questions in reply to Todd Osborne, 01-17-2007 15:35:57  
Hi Todd,
I would suggest you fix the oil pressure problem first. I assume you have checked & cleaned the oil pump screen and put some heavy oil or grease in the oil pump to help it prime. It helps if you have another tractor with a belt pulley so you can belt the D up with the spark plugs out and turn it over without a gage in place to see if you are getting any oil at all. Then maybe start looking for plugged lines, Relief valve problems, etc.
Need to get oil pressure before you run it at all.
Good luck,
Paul

[Log in to Reply]  [No Email]
Todd Osborne

01-17-2007 18:57:18




Report to Moderator
 Re: 38 D oil presure + other questions in reply to Paul from MI, 01-17-2007 18:02:18  
Thanks Paul...I will adhere to your advice on the oil pump prime, One thing I noted in the book I have on Bs it says if the oil pump body is distorted you can loose oil pressure also....this will be yet another item to eliminate in my search for oil pressure some time in the future.... Cheers Todd



[Log in to Reply]  [No Email]
Glen in TX

01-19-2007 08:39:36




Report to Moderator
 Re: 38 D oil presure + other questions in reply to Todd Osborne, 01-17-2007 18:57:18  
Now I see your email wasn't open on other post but I left you info on the oil pressure and pump strainer that needs to be cleaned. Good luck and let us know what you find.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy