Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

720 D Decompression Shaft Seal

Welcome Guest, Log in or Register
Author 
DeereValley

12-29-2006 15:59:57




Report to Moderator

How do you change the seal on the decompression shaft where it goes into the main case? Can I just take the lever off and pop the seal out?

Thank you.




[Log in to Reply]   [No Email]
F-I-T

12-29-2006 16:29:51




Report to Moderator
 Re: 720 D Decompression Shaft Seal in reply to DeereValley, 12-29-2006 15:59:57  
Yes. As long as you can pry it out, that's all you have to do.

Frank



[Log in to Reply]  [No Email]
DeereValley

12-29-2006 17:06:52




Report to Moderator
 Re: 720 D Decompression Shaft Seal in reply to F-I-T, 12-29-2006 16:29:51  
Are there any tricks? Is it hard to do, or will it slip out pretty easy.

Thanks



[Log in to Reply]  [No Email]
F-I-T

12-29-2006 17:48:31




Report to Moderator
 Re: 720 D Decompression Shaft Seal in reply to DeereValley, 12-29-2006 17:06:52  
Well, no tricks I can really think of, other than using a sharp ice pick or awl, or a tiny chisel to split the outside shell which is maybe .020" steel, but most folks drill a small hole or two in the outside surface of the shell (unfortunately it is mostly rubber.....) and use a sheet metal screw welded to the end of a slide hammer for the stubborn ones. I tend toward rolling the old seal inward, until the outside shell is inverted and cut through at one or two places, then yanking it out with a pliers.

If you mess is up, you might have to dive in deeper, but since that is the only other way to remove it, you can only get lucky, or you'll have to go the long route.

Use some Permatex on the outside of the seal to seal it into the recess, and pack a nice dollop of grease behind it, which will help to act as a further seal until hot oil dissolves it in time, or it might stay for a while. Anything to help lessen a chance of further drooling.

Frank

[Log in to Reply]  [No Email]
DeereValley

12-29-2006 18:46:28




Report to Moderator
 Re: 720 D Decompression Shaft Seal in reply to F-I-T, 12-29-2006 17:48:31  
Thanks a lot. We just got it out. We have the reduction cover off so it was a little easier. We took a good screw driver and hit through the steel on the top and was able to work it out. I think this was an easy one though.... I'm sure we will get a hard one soon. Thanks again.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy