Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

4020 Will not Start

Welcome Guest, Log in or Register
Author 
TwoCylinderDiesel

10-23-2006 19:48:38




Report to Moderator

I am working on a friends 1966 4020, when I got to it someone else had removed the injector pump and my friend had a new one, the old one somehow got messed up due to ice in the fuel (or so I am told). The engine was sitting at TDC (per the timing mark) so I just dropped in the new pump, made sure the timing mark lined up in the window and tightened up all the lines. I get fuel when I crack the lines, and it will run if I spray a mist of starting fluid at the air cleaner, but will die quickly without it. I called the guy who took off the old pump and he says he left the engine at TDC on the compression stroke (but I am not sure how he would know that since the valve cover has never been off).
I think it is 180 degrees off on the timing, but this 4020 has a cab so getting the hood and valve cover off to make sure I am on the compression stroke would be a real pain. What would you do?

[Log in to Reply]   [No Email]
msb

10-24-2006 08:15:33




Report to Moderator
 Re: 4020 Will not Start in reply to TwoCylinderDiesel, 10-23-2006 19:48:38  
You don't need to remove the valve cover or anything else.With the flywheel mark on TDC, look down in the hole where the pump goes.There is a vee mark on top of the oil pump drive.The vee mark shoud be in about the 11 o-clock position if the stroke is on #1.Its nearly impossibe to install the pump wrong as the other poster says since the drive tang on the pump shaft is offset.If you were able to just drop the pump in without forcing then it is in the proper place.
Check to be sure you have a full flow of fuel to and from the hand transfer pump.Sounds like you are not getting enough fuel flow somewhere.Also check to see that the fuel return line is not plugged.

[Log in to Reply]  [No Email]
Hayfarmer

10-24-2006 07:15:18




Report to Moderator
 Re: 4020 Will not Start in reply to TwoCylinderDiesel, 10-23-2006 19:48:38  
Did you bleed fuel lines up to the injectors? When I worked on these at a dealership we had a tool that went into the flywheel to make sure timeing was right, pump needs to have lines lined up "dead on" not just next to each other. If injectors set for a while and there was water in the lines perhaps they are not working properly or rusted inside. A dealer should be able to check them for pop off pressure. try the return line first though, may be a bee in it.

[Log in to Reply]  [No Email]
PAP SAYS

10-23-2006 20:45:26




Report to Moderator
 Re: 4020 Will not Start in reply to TwoCylinderDiesel, 10-23-2006 19:48:38  
Make sure the return line back to the tank is open if no fuel return engine will not run on it's own no fuel return will close metering valve in pump. The BOYS



[Log in to Reply]  [No Email]
TwoCylinderDiesel

10-23-2006 22:08:36




Report to Moderator
 Re: 4020 Will not Start in reply to PAP SAYS, 10-23-2006 20:45:26  
I never thought of that, the fuel line from the filter to the pump was clogged so maybe the return line is as well. This has been sitting for about two years outside, with the lines sitting in the cab and everthing else sealed with tinfoil, so who knows what is clogged up. The foil was all intact, so the injectors should be OK. I am thinking I should drain what fuel is in it and replace the filter as well.

[Log in to Reply]  [No Email]
Bob

10-23-2006 20:06:01




Report to Moderator
 Re: 4020 Will not Start in reply to TwoCylinderDiesel, 10-23-2006 19:48:38  
The pump drive is offest, so it will only drop in ONE way.

However, the shaft will go INTO THE PUMP 2 ways, so if it has been partially pulled out of the pump, and turned, it could have been shoved back in 180 degrees off. Often, though, when this happens, the pump shaft seals get cut, and diesel fuel flows into the crankcase.

Or, for something REALLY weird, the oil pump COULD have been installed in the past 180 degrees off, to make up for someone having messed up a PREVIOUS injection pump shaft.

To determine the compression stroke on #1, you can remove it's injector, and note the air rushing out when the engine is coming up on #1 TDC, just as you would remove the spark plug on a gasoline engine to do the same check.

[Log in to Reply]  [No Email]
TwoCylinderDiesel

10-23-2006 22:18:18




Report to Moderator
 Re: 4020 Will not Start in reply to Bob, 10-23-2006 20:06:01  
The story is that it would run really rough, so they pulled the pump, sealed everything up with tinfoil and sent it in to be rebuilt. Two years go by and here I am. The pump was rebuilt in a box, the tin foil was all intact and the timing mark was sitting at TDC. There is no water in the oil (there was duct tape over the pump hole).

As far as finding the compression stroke, I assume the #1 cylinder is the front one. I have ordered a complete shop manual as I am thinking of buying the 4020 once I get it running, so excuse my lack of understanding about it for now. I am used to my R's.

[Log in to Reply]  [No Email]
Bob

10-24-2006 07:56:34




Report to Moderator
 Re: 4020 Will not Start in reply to TwoCylinderDiesel, 10-23-2006 22:18:18  
I hope you get that 4020, as you will REALLY enjoy it!

Yes, #1 is the front cylinder.

Another thing to check... if the old pump had a failed plastic governor damper ring, pieces of it may still be lodged on the fuel return system.

If, for ANY reason, the fuel return system is restriced ANYWHERE between the pump and the tank, the Roosa Master pump will not inject fuel, so the engine won't run.

You can try disconnecting the return line from the rectangular cover on the side of the pump, and try to start it. If the pump has been bled of air, fuel should start dribbling out of the valve/fitting you removed the line from, and the engine should start. (Usual cautions with dripping diesel fuel apply.)

If it DOES start and run with the return line disconnected, then you can check for problems with the line.


All that being said, I ASSUME you've bled the heck out of the filters, the bleed plug opposite the fuel inlet line, at the top of the injection pump, and the high pressure lines at the injectors? They won't start and run until you get nearly ALL the air out of the system.

[Log in to Reply]  [No Email]
TwoCylinderDiesel

10-24-2006 09:42:06




Report to Moderator
 Re: 4020 Will not Start in reply to Bob, 10-24-2006 07:56:34  
I bled the injectors by loosening the fitting near the injector itself and then cranking the engine until fuel dripped out. Is that the right way?



[Log in to Reply]  [No Email]
Jim Black

10-25-2006 04:10:59




Report to Moderator
 Re: 4020 Will not Start in reply to TwoCylinderDiesel, 10-24-2006 09:42:06  
I had the pump on my forty ten rebuilt a few years ago. and when I put it back togather, the only way that it would run was with starting fluid.Pulled the pump and turned the input shaft 180 degrees and tried it a second time.She fired the first timew and ran like a new one.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy