Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

4455 pto lever wont stay engaged

Welcome Guest, Log in or Register
Author 
coreyC

10-02-2006 07:53:39




Report to Moderator

Got a 4455 that when I engage the pto lever to turn on the pto the lever falls back down. Currently using a rope to hold the lever in the engage position. Any ideas?




[Log in to Reply]   [No Email]
8850 dave

10-03-2006 04:14:11




Report to Moderator
 Re: 4455 pto lever wont stay engaged in reply to coreyC, 10-02-2006 07:53:39  
I just finished fixing my 4440 which did just the same, I took the PTO and clutch valve from tractor and found the PTO arm bent and the lock piston stuck. Changed arm and freed piston and works great.



[Log in to Reply]  [No Email]
Tx Jim

10-03-2006 03:56:22




Report to Moderator
 Re: 4455 pto lever wont stay engaged in reply to coreyC, 10-02-2006 07:53:39  
My 4255 pto would do same and I had to replace SGB mounts to correct it as Bob has already stated. On earlier models an arm would bend that was held by the engagement piston in pto control valve and not hold lever engaged. Tx Jim



[Log in to Reply]  [No Email]
G/MAN

10-02-2006 13:29:42




Report to Moderator
 Re: 4455 pto lever wont stay engaged in reply to coreyC, 10-02-2006 07:53:39  
Most common problem is trash built up around the clutch valve, keeping the linkage from traveling fully to allow the lock spool to lock the lever in position. Trace the PTO linkage down to behind the valve and give that area a thorough cleaning. There were also problems with flexing PTO linkage rods, but I think that should have been cured for the 55-series. Could be a problem internally in the valve assembly, but most of the time it's the trash buildup I mentioned.

[Log in to Reply]  [No Email]
Bob

10-02-2006 08:42:14




Report to Moderator
 Re: 4455 pto lever wont stay engaged in reply to coreyC, 10-02-2006 07:53:39  
I'm thinking this setup is pretty much like a 4630 or 4640, for example.

If so, sagged cab mounts, or a rusted, sticky pin in the clevis at the bottom of the rod coming out of the cab, to the valve down below will cause this, as well as if the shaft the passes into the valve gets sticky in it's bore.

More serious, would be a problem inside the PTO valve. Amongst other things, there is a piston in there that holds the lever in the "PTO ON" positionj, after it's been engaged, and then releases only when the lever is pulled back, or the tractor is shut down. There could be a problem there, or with PTO system pressures.

I'd get it checked out, the linkage freed up, and then adjusted to compensate for any sag in the cab mounts, and then check for proper operation and PTO system pressure.

Doing this NOW may save having to split the tractor to replace a burned-out PTO clutch!

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy