Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

Firing sequence on 2 Cyliner Deeres

Welcome Guest, Log in or Register
Author 
Dave in SV

09-28-2006 06:13:23




Report to Moderator

If the two cylinders fire at 180 degrees from each other, then the engine "coasts" for 540 degrees before the next combustion stroke... yet the distributor cap has contacts at 180 degrees... then do the plugs fire at the combustion stroke AND just befoe intake stroke?!?!?!?




[Log in to Reply]   [No Email]
John T

09-28-2006 07:58:13




Report to Moderator
 Re: Firing sequence on 2 Cyliner Deeres in reply to Dave in SV, 09-28-2006 06:13:23  
Dave, Another Yeppers to the gents below, and the fact that on the governor shaft (same RPM as crank) driven ignitions the Delco or non reduction drive mags like the Wico Models X and C (but not the AP I believe) do indeed fire at BOTH Power and Exhaust strokes TDC's, is the same reason why if they are installed 180 degrees out of time (they fit into the governor shafts female drive slot either way) its possible to make em run simply by reversing the top n bottom plug wires. The same IS NOT true on the reduction gear drive mags (some of the FM's and AP I believe) which turn at 1/2 crankshaft speed, i.e. they gotta be installed in time not 180 out and a wire swap wont make em run if so.

John T

[Log in to Reply]  [No Email]
F-I-T

09-28-2006 07:13:57




Report to Moderator
 Re: Firing sequence on 2 Cyliner Deeres in reply to Dave in SV, 09-28-2006 06:13:23  
Yup. Because the governor gear which drives the distributor or mag, is the same size as the crank gear. If they would have made the governor case bigger, they could have fixed that with a 2X governor gear.

Later on, they moved the distributor drive to the cam and the distributor then went to engine half-speed. Early LP's used an external speed reducer between the distributor and the governor flange because they didn't want that lost spark on exhaust to cause backfires into the manifold. Some mag brands, not WICO, had a speed reducer built-in to fire at engine half-speed as well. They were popular on early non-factory LP conversions, as on A's/g's/D's/B's.

[Log in to Reply]  [No Email]
Bob

09-28-2006 07:09:10




Report to Moderator
 Re: Firing sequence on 2 Cyliner Deeres in reply to Dave in SV, 09-28-2006 06:13:23  
On the mags that have the rotor on the magneto's mainshaft, EACH plug fires every 180 degrees, whether that cylinder is on the compression stroke, or not.

If the mag has a "half-time" shaft, such as the Edison Splitdorf CD-2, the points and rotor are on the half-time shaft, and each cylinder gets a spark only when needed. The point cam is asymetrical, with the cam lobes spaced at 180 and 540 degrees.

[Log in to Reply]  [No Email]
ebbsspeed

09-28-2006 08:18:11




Report to Moderator
 Re: Firing sequence on 2 Cyliner Deeres in reply to Bob, 09-28-2006 07:09:10  
Bob, your statement that "On the mags that have the rotor on the magneto's mainshaft, EACH plug fires every 180 degrees, whether that cylinder is on the compression stroke, or not." isn't quite correct. Each plug fires every 360 degrees of crankshaft rotation, but they fire 180 degrees from each other. If both plugs fired every 180 degrees they would be firing at the top and bottom of every sroke. While this would be OK at the beginning of the intake, combustion and exhaust strokes (ie, end of exhaust, compression and combustion), it would be detrimental to proper operation if it were to occur at the beginning of the compression/end of intake stroke, don'tcha think?

[Log in to Reply]  [No Email]
Bob

09-28-2006 14:35:18




Report to Moderator
 Re: Firing sequence on 2 Cyliner Deeres in reply to ebbsspeed, 09-28-2006 08:18:11  
Change the term "EACH plug" to "A plug" fires every 180 degrees. I was trying to type FAST, to finish the post, with the PPSU standing over me, waiting to drive 35 miles to WaldoWorld... O, what a JOY!

Ever had a flooded "D" fire with an exhaust valve open, while you have rocked forward, while hand-cranking the flywheel, so that the side of your face is next to the sectional cast iron muffler, and the resulting explosion BREAKS the muffler?

NOT FUN, and I haven't started the "D" again, since! I have an Edison Splitdorf mag for it, which will eliminate the "firing with an exhaust valve open" trick, but I can't seem to get around to installing it!

[Log in to Reply]  [No Email]
John T

09-28-2006 10:02:49




Report to Moderator
 Re: Firing sequence on 2 Cyliner Deeres in reply to ebbsspeed, 09-28-2006 08:18:11  
Ebbs, Until Bob gets here I agree with ya (The "Coil" does indeed fire every 180) he knowns darn well how they work, but if hes anything like me (sure hope not for his sake lol) and trying to answer questions n give help to so many others especially in a hurry, my fingers get ahead of my old brain now n then lol. Often times gents such as The Frankster (aka FIT) or Glen in Tx or Duane or Clooney in the old days helped or corrected my errors which sometimes were NOT typos or brain farts or senior moments, but plain old ignorance grrrrr r and I in turn enjoy helping others also, ita a great hobby and a bunch of fine folks is what I enjoy the most

Good point on the firing, yall take care now

John T

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy