Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

630 Starts then dies

Welcome Guest, Log in or Register
Author 
CFWelles

09-16-2006 09:48:23




Report to Moderator

I just started a 630 that I have owned for about one year and ran no more than two or three hours. Tractor fired up and ran for about thirty seconds then died fairly quickly...I kept it going a short time more by choking it. I believe the issue to be inside the carburetor as there is good gas flow into it. When inlet nut is loosened, gas starts to run out in good volume. Does anyone know if these are prone to float and needle issues and/or dirt. Sediment bowl shows some rust in bottom. I believe I am going to have to take carb off, disassemble, blow out and clean out, then reassemble. Am I on the right track? Also after sitting a while, tractor will start and do same thing. Checked tank and there is adequate gas level in tank. Will check spark, but doubt that is the issue here. Any comments from those of you with more experience with these carbs?

[Log in to Reply]   [No Email]
CFWelles

09-17-2006 20:30:18




Report to Moderator
 Re: 630 Starts then dies in reply to CFWelles, 09-16-2006 09:48:23  
Dropped the carb bowl and found the float needle to be hanging up a little. Don't know why because she was clean as a whistle on the inside. Looked to me like carb was rebuilt shortly before I bought it. Ran some carb cleaner though the fuel inlet to the carb and blew out with air. When reassembled the float and needle worked just fine. Thanks for your input. Have the tractor up for sale in the photo section...630 row crop. Hate to offer the tractor for sale, but am out of space and have a 730 propane project that needs to go inside.

[Log in to Reply]  [No Email]
DP

09-16-2006 10:51:43




Report to Moderator
 Re: 630 Starts then dies in reply to CFWelles, 09-16-2006 09:48:23  
Does your 630 have the automatic fuel shutoff above the sediment bowl? Take the fuel line off the carb. and put a can or something under it to catch gas. Then hold the button on top of the automatic shutoff down for probably a minute and see if it maintains a full flow. Every tractor I have with that setup, I've had to remove the shutoff and completly dissamble, and clean out. Over years they get plugged up. While your there, you might want to replace the diaphram rubbers as well. Good luck with your problem. Don

[Log in to Reply]  [No Email]
CFWelles

09-16-2006 14:23:00




Report to Moderator
 Re: 630 Starts then dies in reply to DP, 09-16-2006 10:51:43  
Thanks for the suggestion. Mine is equipped with the auto shutoff. I will perform this check and let you know if that's the problem.



[Log in to Reply]  [No Email]
Bob

09-16-2006 10:45:25




Report to Moderator
 Re: 630 Starts then dies in reply to CFWelles, 09-16-2006 09:48:23  
You say "When inlet nut is loosened, gas STARTS to run out in good volume."

That is MEANINGLESS with your problem.

You need to open up the floatbowl drain.

SAFELY, catch the fuel, and allow it to continue to drain for a minute or two.

I think you will see the flow taper off to almost
nothing, as the float bowl empties, and is not being adequately replenished by the flow from the tank, through the sediment bowl and shutoff, and past the needle and seat, into the float bowl.

That's why it runs for a little while and quits... when it has used up the fuel that has slowly trickled into the float bowl, before you started it.

Check it out... find where the fuel flow restriction is.

[Log in to Reply]  [No Email]
CFWelles

09-16-2006 14:28:43




Report to Moderator
 Re: 630 Starts then dies in reply to Bob, 09-16-2006 10:45:25  
Thanks for your commment. Thought that my check at carburetor inlet was showing good flow from the sediment bowl into the carburetor. From other suggestion realize that the problem can be either in sediment bowl under tank or in carburetor. Will do a little more checking to find which one is the source of restriction.



[Log in to Reply]  [No Email]
Gerald J.

09-16-2006 15:04:38




Report to Moderator
 Re: 630 Starts then dies in reply to CFWelles, 09-16-2006 14:28:43  
The flare to carburetor adapter OFTEN includes a screen. That screen has been known to gather varnish and dirt and plug up. I saw one on a JD2020 about 4 years ago that wouldn't pass air at 60 psi. It sure didn't pass much gas at 1/4 psi.

Then varnish could have stuck the float valve almost closed or even stuck the float so it won't let the float valve open.

So its essential to check fuel flow from the float bowl drain, else you've skipped checking three parts of the fuel system that are known to cause your exact symptoms.

Gerald J.

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy