Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

4020 Steering HELP!

Welcome Guest, Log in or Register
Author 
Matt in PA

05-30-2006 17:53:08




Report to Moderator

Hello,

I was baling hay the other day and got my feet wet w/ hydralic oil coming from the top of my '69 4020's steering column. I looked in my parts book and it calls for a seal kit in the end of the steering column. How much of a job is this? And do I need to bleed the steering system when I have replaced it? I check the archives, but did not find anything on this particular problem. Any help will be much appreciated! Thanks, Matt

[Log in to Reply]   [No Email]
Matt in PA

05-31-2006 17:15:08




Report to Moderator
 Re: 4020 Steering HELP! in reply to Matt in PA, 05-30-2006 17:53:08  
Thanks for the help! It will be this weekends job.

Matt



[Log in to Reply]  [No Email]
Bob

05-30-2006 18:15:36




Report to Moderator
 Re: 4020 Steering HELP! in reply to Matt in PA, 05-30-2006 17:53:08  
Remove the steering wheel, and the throttle lever.

The snap ring, washer, and seals are then exposed.

Use a small slide hammer puller with a sheet metal screw to pull the seals. (Be carefull not to damage the shaft or bore.)

Install the new seal parts in the correct order,and put the throttle lever and steering wheel back on. The steering will likely bleed itself upon startup, when the wheel is cycled completely right and left a couple of times.

IIRC, there is another seal and backup ring way down inside that requires the steering unit to be completely diassembled, but I have been lucky a couple of times, and simply replaced the top seal parts, and all was well.

[Log in to Reply]  [No Email]
msb

05-30-2006 20:39:42




Report to Moderator
 Re: 4020 Steering HELP! in reply to Bob, 05-30-2006 18:15:36  
Right you are Bob about being lucky.I have never been so lucky.I have always had to do the complete overhaul.But it doesn't hurt to try.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy