Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

Deere #33 vegetable planter question

Welcome Guest, Log in or Register
Author 
Brendon

05-01-2006 18:41:25




Report to Moderator

Anyone know what years Deere built the #33 vegetable planter units? Also, is there any info out there as to about how many were produced? Thanks.




[Log in to Reply]   [No Email]
Glen in TX

05-02-2006 12:04:43




Report to Moderator
 Re: Deere #33 vegetable planter question in reply to Brendon, 05-01-2006 18:41:25  
Last parts catalog I see printed for it by 1994 JD publications catalog was in Feb. 1980. That doesn't mean it was made that long but just that the last version of parts catalog was printed then. PC1045 Parts Catalog and OMA25188 Operators Manual. Sometimes implement parts catalogs show years if updates or different versions were made. Local dealer might have a manual or you can order them from JD Publications 800-522-7448. Is it the planter with small square boxes and long seed tubes with a shoe like a drill? Or am I thinking of the old beet planters? Use to be some those around here and many used them for planting beets and also double row milo but not anymore.

[Log in to Reply]  [No Email]
Brendon

05-02-2006 19:49:44




Report to Moderator
 Re: Deere #33 vegetable planter question in reply to Glen in TX, 05-02-2006 12:04:43  
Thanks for the info. The ASAE John Deere Vol II book seems to suggest that they were still available at the time of the book's printing in 1990 but there is no definate dates shown. It could be they didn't change much and the tech publications were not revised for a long time.

These are the planter units that had a small, round seed hopper mounted low in the frame at about a 45 degree angle. The plates were machined stainless steel (completely different than they standard Deere plates) and the hopper bottom was also machined to close tolerances. The plates picked up seeds at the bottom of the hopper then carried them around to the top of their travel where a brush cut-off sent them down the seed tube. The runner was very short and very similar to what you would find on a Planet Jr seeder. The drive wheel was in front with a smaller packer wheel in back. I recently picked up a couple units in Colorado mostly for the novelty of it. They are virtually unheard of here in Kansas and will be neat to have at our local antique tractor show.

[Log in to Reply]  [No Email]
Glen in TX

05-02-2006 22:05:28




Report to Moderator
 Re: Deere #33 vegetable planter question in reply to Brendon, 05-02-2006 19:49:44  
Ok, I've seen those before but never realized the plates were stainless. Guess you can always plant a garden with them. Funny you mentioned getting them in Colorado and I may have seen some there before. My uncle use to deal in all kinds of machinery in the San Luis Valley area. We once had some of those Planet Jr. units too and wish I had never sold them.



[Log in to Reply]  [No Email]
Brendon

05-03-2006 04:10:03




Report to Moderator
 Re: Deere #33 vegetable planter question in reply to Glen in TX, 05-02-2006 22:05:28  
These came from SE Colorado just a few miles from where I grew up. There used to be a lot of produce grown there and there still is some but it has slowed down some with the difficult water situation in that area. The area was best known for cataloupes and watermelons.

The only catch with actually using the planter in my garden is the shocking price of the seed plates. I was fortunate to get three sets with mine but to order them from Deere would cost over $120 per plate according to the jdparts website. Just a single plate would cost more than I paid for the entire setup!

[Log in to Reply]  [No Email]
Glen in TX

05-03-2006 08:23:45




Report to Moderator
 Re: Deere #33 vegetable planter question in reply to Brendon, 05-03-2006 04:10:03  
Wow, a person needs to make sure they get plates with them then. Think it was mostly potatoes, hay, barley, and hops grown last time I visited around Alamosa, Center, Monte Vista, La Jara areas. About as close to the SE corner as I've ever been was Raton pass area.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy