Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

'49 A connecting rod bearing confusion

Welcome Guest, Log in or Register
Author 
Rutland

04-11-2006 07:00:24




Report to Moderator

After removing the cylinder block from my �49 A serial # 645819 to get at the broken block studs (4 out of 6) I found that the connecting rods non-removable babbitt bearings have definitely seen the course. The rods have casting numbers A2234R and A2234L. It appears that at some time JD replaced these rods with new connecting rods that accepted insert type bearings. The way I�m reading the JD parts manual the new rod part numbers is AA5350R and AA5351R is the bearing number. But under the description column for part number AA5350 they refer to the rod number as A4648R. I totally confused. I would like to replace the old rods with the newer type that have the bearing inserts, but at this point I�m not sure what part numbers I should be looking for, or were to look for them. I�d sure appreciate any help I could get, at this point I�m sort of �dead in the water�. Thanks, Rutland

[Log in to Reply]   [No Email]
Rutland

04-11-2006 12:40:51




Report to Moderator
 Re: '49 A connecting rod bearing confusion in reply to Rutland, 04-11-2006 07:00:24  
Gentlemen, I�m very grateful for your response. There maybe hope yet.
F-I-T, it looks like your suggestion about getting a set of rods from a JD Model 60 might be my best bet. Both of my �How to Restore Books� and my JD manuals only deal with the letter series tractors, although T. Gaines book shows a picture of a model 60 and said it was introduced in 1952 as an updated and enhanced version of the Model A. That is all I know about the Model 60, is it time now to get another book(s) on the Model 60. Do you happen to know if the wrist pin size is the same as the �A� rods? I�d like to use my original cast iron pistons. I think there ok. I got 100 psi in each cylinder before I tore it down. Is the 60 model �new� enough that a set of new rods and bearings are available, and could you give me a few suggestion on where to look for them.

Mike, at this point I�m a bit leery of buying used rods from eBay. That is what got me to this point. Caveat Emptor raised it�s ugly head again. My fault. The seller had a very long list of excellent feed-backs, how could I go wrong (ha). His claim that the engine had been professionally rebuilt leads me to wonder who this so called pro. was. Broken block studs, cracked block and a carb. that belonged on a Model B. He was a 1000 mile away and the check was cashed and being a greenhorn at this it took me a while to find it all out. I know I�m not the first nor will I be the last. Thanks again for all your help, I know I�ll be back again with more questions. Rutland

[Log in to Reply]  [No Email]
F-I-T

04-11-2006 13:52:21




Report to Moderator
 Re: '49 A connecting rod bearing confusion in reply to Rutland, 04-11-2006 12:40:51  
"Do you happen to know if the wrist pin size is the same as the �A� rods? I�d like to use my original cast iron pistons."

The numbers I quoted are the same for the "A" after 488,000 using insert type bearings and the Model '60' (I think the "A" came out with babbit only rods, and when the '60' came out with the inserted type rod, those were all that were offered for replacement parts going forward).

Anyway, the late "A" uses the same piston (AA 4338 R), piston pin (A 2339 R) and piston pin bushing (A 2343 R) as the '60'.

Frank

[Log in to Reply]  [No Email]
Mike M

04-11-2006 10:23:07




Report to Moderator
 Re: '49 A connecting rod bearing confusion in reply to Rutland, 04-11-2006 07:00:24  
Check out ebay for a deal on some of the rods made for inserts that fit in A and 60 models. And also price having a local machine shop rebore yours out for the inserts to fit in them.There are places to get them rebabbited but I haven't had any done in years. I have just found another set of good used ones and put them in as it is usually cheaper.



[Log in to Reply]  [No Email]
jdhbag

04-11-2006 09:22:12




Report to Moderator
 Re: '49 A connecting rod bearing confusion in reply to Rutland, 04-11-2006 07:00:24  
You might try Paul's Rod and Bearing in Parkville,MO. (816) 587-4747. I havent tried them as of yet but have been told they do good work. There are others out there also but i dont have their information at hand right now.



[Log in to Reply]  [No Email]
F-I-T

04-11-2006 09:17:21




Report to Moderator
 Re: '49 A connecting rod bearing confusion in reply to Rutland, 04-11-2006 07:00:24  
R:

I think I can help.

You said

"The way I�m reading the JD parts manual the new rod part numbers is AA5350R and AA5351R is the bearing number. But under the description column for part number AA5350 they refer to the rod number as A4648R. I totally confused. "

The "A 4648 R" is an "A" part number, and it is probably the number that is cast into the rod. If you add a wrist pin bushing (A 2343 R) to a A 4648 R rod you get an "A" "Assembly" part or an "AA" followed by numbers, in this case AA 5350 R.

So if you wanted to order a new rod "assembly" from Deere which would include a rod, wrist pin bushing, you would order a AA 5350 R. I'm not sure you could have ordered just a bare rod or not back in the day.

BTW, the rods from a '60 will work in your late "A" as well.

Frank

[Log in to Reply]  [No Email]
mike in shendoah valley

04-11-2006 09:13:18




Report to Moderator
 Re: '49 A connecting rod bearing confusion in reply to Rutland, 04-11-2006 07:00:24  
Rutland-there wiil be several posts coming with the part #'s you want from guys that really know. All i can say is that i replaced mine with rods out of a "60" don't know part #'s



[Log in to Reply]  [No Email]
Rutland

04-11-2006 08:51:39




Report to Moderator
 Re: '49 A connecting rod bearing confusion in reply to Rutland, 04-11-2006 07:00:24  
In the event that the connecting rods with inserts were not available is it possible to get the original ones I have re- babbitted. If so does anyone know of a good shop that could do this for me. Thanks again, Rutland



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy