Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

49 JD A oil pump adjustment

Welcome Guest, Log in or Register
Author 
ChadS

03-21-2006 08:06:11




Report to Moderator

Im working on a 49 A that has the engine rebuilt recently. The oil pump pressure adjustment is stuck on it, Do I have to remove the pump to fix this, or can it be fixed in the tractor? It carries just above the "L" at idle, just below M at full throttle, what should the pressure be reading? M at an idle? Also, I have to set the endplay on the crankshaft by resetting the flywheel position on the crank,,, The clutch dont enguage correctly, I belive it is because of the endplay is too loose, but hoping the harmonic balancer is still good and the splines are in good shape,, Any suggestions?? Thank you! ChadS

[Log in to Reply]   [No Email]
Maark

03-21-2006 09:54:52




Report to Moderator
 Re: 49 JD A oil pump adjustment in reply to ChadS, 03-21-2006 08:06:11  
That oil pressure is probably correct for your A. If you have excessive endplay it could affect your clutch. You will need to block your clutch pulley from moving, then loosen the flywheel and tap it in. Should have around .005 endplay. Make sure those flywheel bolts are tight afterward. They will work loose. You might even install new grade 8 bolts.



[Log in to Reply]  [No Email]
ChadS

03-21-2006 10:20:49




Report to Moderator
 Re: 49 JD A oil pump adjustment in reply to Maark, 03-21-2006 09:54:52  
The clutch, the bushings in the vertical shaft are shot, the whole top of the shaft moves back n forth quite a bit. I adjusted the pressure plate, and went to try it out, well,, the hand lever moves, but the excessive play in the top bushing is so sloppy it's not allowing anything to move inside the clutch. I would imagine the shaft itself also has a groove worn into it too, Do they make those bushings still? I can rebuild the shaft up,, or make the bushings if I had to,,, When I go to remove the whole assembly, after removing the 4 bolts that hold it to the engine housing,,, do I have to remove the entire clutch, Harmonic balancer, and slide the belt pulley out so I can get the assembly out? or can the pulley be left alone? Its been a while since Ive torn one of these apart. ChadS

[Log in to Reply]  [No Email]
BUDD

03-22-2006 14:06:12




Report to Moderator
 Re: 49 JD A oil pump adjustment in reply to ChadS, 03-21-2006 10:20:49  
Chads;

I got mine shaft fixed and bushing done in Goshen. I can not think of the name off the top of my head. It is a small machine shop across from nape area on 33 south side of town. It cost me about $125 to get it done, but what a difference it made. BUDD



[Log in to Reply]  [No Email]
ChadS

03-24-2006 12:23:27




Report to Moderator
 Re: 49 JD A oil pump adjustment in reply to BUDD, 03-22-2006 14:06:12  
The shaft is broken in two. Just got the parts to put back together. I think this ol A runs bout like yours does,,,,, strong. Chad



[Log in to Reply]  [No Email]
Glen in TX

03-21-2006 12:37:56




Report to Moderator
 Re: 49 JD A oil pump adjustment in reply to ChadS, 03-21-2006 10:20:49  
Recommended flywheel end play is .005" - .010" with no binding while turning over engine. Recommended oil pressure for A is 10-15 psi with engine at operating temperature. A JD guage should read between M and H. Check tractor with another known good oil guage. I&T JD-4 covers all this and setting the oil pressure and pump overhaul and clutch overhaul if needed.

On the clutch brake pulley assembly you can remove the 4 bolts and slide it out the front. Make sure all of the fork is there and nothing broke off or chipped off sleeve inside. Bushings are not a item available from JD for that shaft so have to make them or find some to size and fit and build up shaft and/or splines like you talk about. Replace or rebuilt the pins and holes in clutch linkage rods also. It is good to remove the clutch pulley and inspect the linings for wear or cracked and broke linings and regrease the clutch pulley bearing and inspect the toggle dogs and regrease them also. Search archives here as someone had recently posted having their clutch brake and fork rebuilt by someone in the midwest and price sounded reasonable to me.

[Log in to Reply]  [No Email]
Glen in TX

03-21-2006 12:55:58




Report to Moderator
 Re: 49 JD A oil pump adjustment in reply to Glen in TX, 03-21-2006 12:37:56  
Also.. Make sure the flywheel splines are aligned properly and it is on crankshaft correctly. Check that the pin in flywheel engages the slot in the oil slinger ring also. If you have the flywheel off check the pin and slinger for wear. It doesn't cost much to put the cork seal in on the slinger either behind the bearing cover.



[Log in to Reply]  [No Email]
ChadS

03-21-2006 13:07:26




Report to Moderator
 Re: 49 JD A oil pump adjustment in reply to Glen in TX, 03-21-2006 12:55:58  
Thank Ya! I got the fork removed, no problem. It looks a little worn though,, it has wear pads on the fork, I was thinking they was thicker than what it is,, Does anyone have a good fork to take a thickness measurement? The crank end play is at .005, so its good. It just looks like the parts for the clutch is needed to be rebuilt. Yep, all the pins are shot, making all new ones. ChadS



[Log in to Reply]  [No Email]
Glen in TX

03-21-2006 14:45:02




Report to Moderator
 Re: 49 JD A oil pump adjustment in reply to ChadS, 03-21-2006 13:07:26  
See the post above for clutch rebuilding.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy