Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

Broken Manifold Bolts

Welcome Guest, Log in or Register
Author 
RFH

03-06-2006 04:48:49




Report to Moderator

This isn't a John Deere quaetion, but I thought one of you folks could help. I have a Dodge Ram 2500 with a 360 ci engine. Two of the bolts holding on the exhaust manifold have sheared flush to the engine, I don't know how. How the heck do I go about getting them out of there?




[Log in to Reply]   [No Email]
TIMAR

03-06-2006 18:28:05




Report to Moderator
 Re: Broken Manifold Bolts in reply to RFH, 03-06-2006 04:48:49  
Just did this on my 630 head to manifold bolts. What worked for me is to heat the stud up cherry red and weld a nut to it while it is hot and them walk away and let it cool off. I came back an hour later and they turned out real easy. I would turn them a little both ways until I could tell it was going to come out. Maybe I was lucky, but I was lucky four times then.



[Log in to Reply]  [No Email]
TSX

03-06-2006 14:56:58




Report to Moderator
 Re: Broken Manifold Bolts in reply to RFH, 03-06-2006 04:48:49  
RFH,

I thoroughly recommend the easy-out, they are really easy to use...just kidding. I broke a head off of a bold that went into the manifold of my 51 JD...it was flush to the top...infact, it was concave and when the head broke off, it took some of the bold below the line...here is my commment...make sure you are using very sharp metal bits when you start drilling...the drill bit broke off in my head bolt and you think an easy out is hard to remove...anyway, alot of heat and sharper bits finally removed the bolt, plus an entire saturday wasted!!!

tstex

[Log in to Reply]  [No Email]
Tom Windsor

03-06-2006 14:32:35




Report to Moderator
 Re: Broken Manifold Bolts in reply to RFH, 03-06-2006 04:48:49  
All of the responses are good ones...stay away from an easy out!!!

What works for me is, I center punch the hole. Then I drill a small hole all the way through; then increase the size of the drill; then keeping an eye on my size, I go up as far as I can go without getting into the threads. Then, I either burn out the residue as suggested herein or if there is room, I get a small pointed chizzle and tap it a little--carefully. If you are lucky, it will pull away from the wall and out it will come...usually, I pump up the oxygen and burn it out after i have drilled it out...then follow behind it with a tap. STAY AWAY FROM AN EASY OUT...ONCE YOU BREAK IT OFF IN THERE...YOU WILL NEVER SEE THE BOTTOM OF THE HOLE AGAIN...THE ONLY WAY TO GET THAT OUT IS TO CHIP,CHIP,CHIP FOR ABOUT A DAY.

[Log in to Reply]  [No Email]
Henry M

03-06-2006 11:54:44




Report to Moderator
 Re: Broken Manifold Bolts in reply to RFH, 03-06-2006 04:48:49  
rfh

You hanen't had any fun until you break off an easy out in a broken off bolt. I only did that once and that was decades ago.

Same as above, I wouldn't go there.



[Log in to Reply]  [No Email]
ET

03-06-2006 06:49:43




Report to Moderator
 Re: Broken Manifold Bolts in reply to RFH, 03-06-2006 04:48:49  
If the head is off the easiest way is to weld a nut on the broken stud.I have had some luck with getting them out with a cutting torch by cranking the oxygen up to about 50lbs and burning them out. The steel with burn but not the cast iron. If you can drill a small hole through the broken bolt first it helps. Run a tap in the threads when you get done. The metal blowing back at you may plug some of the torch tip so you will have to clean it. good luck

[Log in to Reply]  [No Email]
Henry M

03-06-2006 05:42:00




Report to Moderator
 Re: Broken Manifold Bolts in reply to RFH, 03-06-2006 04:48:49  
rfh

A common attempt would be to place a nut over the bolt end and weld the center full or at least the nut firmly to the bolt and it should spin out. Careful not to weld the nut to the head.

Hope you can get in there.



[Log in to Reply]  [No Email]
RFH

03-06-2006 07:57:16




Report to Moderator
 Re: Broken Manifold Bolts in reply to Henry M, 03-06-2006 05:42:00  
I don't believe there is enough there to get a weld on. Could you drill a smaller hole into the center of the bolt and try to get an easy out in there? Probably a lot easier said than done.



[Log in to Reply]  [No Email]
Bob

03-06-2006 08:18:16




Report to Moderator
 Re: Broken Manifold Bolts in reply to RFH, 03-06-2006 07:57:16  
Even if the bolt is broken off flush, or even slightly recessed, you can weld a flat washer to it. Burn the weld in as much as possible, to heat the bolt as much as possible.

Allow it to cool to ambient temperature, then weld a larger nut to the flat washer. Using a larger nut will allow you to weld through the inside of the nut, onto the washer.

Again, let it cool to ambient temperature. As soon as it has cooled enough to be safe, begin spraying a good loosen juice on it.

(The heating and cooling cycles help break the bolt loose from the head.)

Hopefully, the bolt will then come out on the first try, if not repeat the whole process.

I would caution against using an "easy-out" because if the bolt broke because it was badly stuck in the head, you will only break the "easy-out" off in there, making matters worse.

Unless a bolt has been broken off by stress, and is not really stuck in place, "easy-outs" AREN'T.

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy