Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

4020 hydro oil return.

Welcome Guest, Log in or Register
Author 
Nylon

09-06-2005 19:03:01




Report to Moderator

Hi,

I am about to set up a joystick on my 4020. I have a hydro hose rather than steel for rock shaft supply and am deciding which end to T off of. I am trying to figure out where the return oil lines are. I am still waiting on operators manual and service manual doesn't indicate. I have 2 large lines and one smaller line leading out from just behind the hydro filter. Are these return lines? One big one looks like it leads up front to the front pump so I don't know if this is a supply or a return. Any help would be great.
I want to T into a return line rather than dump into filter cover.
Thanks,
John

[Log in to Reply]   [No Email]
buickanddeere

09-08-2005 09:18:05




Report to Moderator
 Re: 4020 hydro oil return. in reply to Nylon, 09-06-2005 19:03:01  
Bob is 100% correct.



[Log in to Reply]  [No Email]
Bob

09-06-2005 22:28:09




Report to Moderator
 Re: 4020 hydro oil return. in reply to Nylon, 09-06-2005 19:03:01  
Do it right and dump the return into the filter cover.

That way, it is filtered, and cooled. Besides the filter, there are pressure regulating and cooler relief valves, and you want the return oil flow in the right place in relation to them.

Sometimes, it's better to bite the bullet and just do things the right way.

You do NOT want to put unfiltered oil in the charge flow to the front pump.

[Log in to Reply]  [No Email]
Mike M

09-07-2005 09:56:20




Report to Moderator
 Re: 4020 hydro oil return. in reply to Bob, 09-06-2005 22:28:09  
When John Deere used those models for industrial units they did not dump the return oil back into the filter cover. I had a 500 that returned the oil back to the left hand side near the bottom.I'd have to go look up what this is called but when I hooked up my 4020 loader I copied this setup and drilled and tapped a fitting in this area for my return.



[Log in to Reply]  [No Email]
Nylon

09-07-2005 12:06:37




Report to Moderator
 Re: 4020 hydro oil return. in reply to Mike M, 09-07-2005 09:56:20  
Mike,

Did this essentially dump the oil back into the reservoir? Which then got sucked into the sump screen and then the filter? I had asked my jd dealer about doing this a while back and my memory is thin but I believe they said they tapped a T into the rockshaft return oil. I do want to dump return oil into a place where it goes to reservoir then screen then filter to be safe. I cant tell exactly where the rockshaft return oil is or if it is internal.

Thanks,
John

[Log in to Reply]  [No Email]
Nylon

09-07-2005 00:28:28




Report to Moderator
 Re: 4020 hydro oil return. in reply to Bob, 09-06-2005 22:28:09  
Thanks for the info Bob. I assumed that the return lines would dump into the reservoir which would then be filtered before getting picked up into the pump. I didn't want to dump into the filter cover because that makes taking off the filter cover that much more of a mess and work.

John



[Log in to Reply]  [No Email]
Bob

09-07-2005 07:47:50




Report to Moderator
 Re: 4020 hydro oil return. in reply to Nylon, 09-07-2005 00:28:28  
The return oil DOES NOT return to the sump. It is filtered, and then flows forward to the oil cooler and pump. Any flow in excess of the front pump's needs at a given moment flows back to the transmission, where it lubes the bearings and gears.

I have seen many of the "filter cover return" setups where they have put a quick-disconnect hydraulic coupler next to the filter cover. This allows the hose to be quickly disconnected from the filter cover for filter changes with minimum oil loss, and makes it easy to change the filter without the cover dangling from a stiff hose.

[Log in to Reply]  [No Email]
Nylon

09-07-2005 08:51:27




Report to Moderator
 Re: 4020 hydro oil return. in reply to Bob, 09-07-2005 07:47:50  
Thanks again Bob.

That is what I will do. That makes taking off that cover useful.

So those return lines dont go to the filter and sump? It continuously gets used until it becomes excess where it then gets filtered?

Thanks,
John



[Log in to Reply]  [No Email]
Bob

09-07-2005 13:57:07




Report to Moderator
 Re: 4020 hydro oil return. in reply to Nylon, 09-07-2005 08:51:27  
As I stated before, the return oil is filtered, flows up front through the oil cooler, and THEN what is not needed by the front pump returns to the transmission shafts and bearings, and THEN to the sump.



[Log in to Reply]  [No Email]
Nylon

09-07-2005 16:16:04




Report to Moderator
 Re: 4020 hydro oil return. in reply to Bob, 09-07-2005 13:57:07  
Bob thanks.

I have been block headed but the process seemed to defy my mental capacity. I will have to look at a diagram to see how that works. Seems odd that unneeded oil would go to reservoir. I can see where supplying the front pump as much as possible is good idea just don't see how it can accompish that.

I see a five gallon bucket as a reservoir with a strainer and a fine screen leading to a pump intake and everything circulating from there. Everything then being returned to the top of the five gallon bucket after it has passed through each users lines.

Sounds like oil is recirculated to the front pump without going back through the sump and strainers unless it is in excess of what is on demand. I guess I cant visualize how excess oil under pressure is diverted.

I will find a cover or make a threaded hole with quick connect as I want that return oil filtered and ready. Thanks for putting up with my density :]

John

[Log in to Reply]  [No Email]
Bob

09-07-2005 20:02:34




Report to Moderator
 Re: 4020 hydro oil return. in reply to Nylon, 09-07-2005 16:16:04  
Nylon,

The return oil (and the oil from the transmission pump) gets pumped up front, and feeds the front pump at low pressure that the oil cooler can withstand. It is essentially tee'd off, and the amount not used by the front pump is returned to the tranmission as lube at low pressure, much like the lube oil pressure in an engine.

When no hydraulic functions are being used, the front pump takes almost no oil, and nearly all the oil from the transmission pump is returned to the tranny as lube. (Of course, since there are no functions being used, there is very little function return oil at that time.)

When you use a hydraulic function, such as lifting the loader, the return oil coming back from the loader valve is filtered and added to the flow from the transmission pump, and made available to the front pump, so it isn't starved for oil. This is especially important when you depress the clutch, as the transmission pump then stops, and the only oil available to the front pump is the oil stored in the oil cooler, with the function return oil replenishing it.

[Log in to Reply]  [No Email]
Nylon

09-07-2005 23:36:08




Report to Moderator
 Re: 4020 hydro oil return. in reply to Bob, 09-07-2005 20:02:34  
Bob,

Ah thank you again. Now for a partially educated question. Why is the transfer pump associated with the clutch? The transfer pump is low pressure and floods the supply to the front hi pressure pump til a demand takes it. And is driven off of the transmission rather than a constant pump at high pressure run off the engine? So therefore hi pressure only supplied on demand and less wear to a hi pressure pump while a low pressure pump easily supplies vitals.

Starving loader function is a bugger though because so much loader function is done with the clutch in. I know that there is oil supplied to both sides of the packings in a cylinder. When you are raising the loader, oil is pumped into one side while the other side is drained. This drained oil then goes to the filter. Does this return oil go to the filter and then back to the hi pressure pump without having to use the transfer pump here? Or does the transfer pump help move it along at this stage with other flow?

Last dumb question is this. If synchroshift is in neutral and not park with the clutch out, does transfer pump run at this point? I would assume that it does but don't know for sure.

Thanks again,
John

[Log in to Reply]  [No Email]
Bob

09-08-2005 06:50:17




Report to Moderator
 Re: 4020 hydro oil return. in reply to Nylon, 09-07-2005 23:36:08  
1.) The transmission pump is driven off of the tranny's top shaft, and only runs when your foot is off of the clutch pedal.

2.) The function return oil is tee'd into the flow from the tranny pump, so it's ADDED to the flow from the tranny pump before the filter. There is a check valve that prevents charge oil from back flowing to the tranny pump at shutdown, or when the clutch is depressed.

So, when the clutch is depressed, the front pump is fed from the oil stored in the cooler, which is being replenished by function return oil. Due to leaks to sump in various parts of the hydraulic system, eventually the cooler will empty out, and won't get filled again until the foot clutch is engaged.

3.) The transmission pump runs whenever the clutch pedal is not depressed, and the engine is running.

[Log in to Reply]  [No Email]
Mike M

09-07-2005 19:33:37




Report to Moderator
 Re: 4020 hydro oil return. in reply to Nylon, 09-07-2005 16:16:04  
I would be careful about using quick connectors under there as I think they could easily get disconnected by some brush. On a closed center system it would just be a nuisance ,but I have seen these used on open center systems with bad out come. Once they get popped off the hose is blocked makeing a dead end that can shear off the pump shaft.



[Log in to Reply]  [No Email]
Bob

09-07-2005 20:09:00




Report to Moderator
 Re: 4020 hydro oil return. in reply to Mike M, 09-07-2005 19:33:37  
Since this is a closed center system, why bring up the "open center" broken pump shaft scenario? It does not apply here.

Furthermore, I have been around quite a number of these 4010's and 4020's with the quick disconnect at the filter cover, and can't ever remember anyone complaining about the hose coming undone, and these tractors are used all the time in hayfields, brush, etc..



[Log in to Reply]  [No Email]
Mike M

09-08-2005 09:35:03




Report to Moderator
 Re: 4020 hydro oil return. in reply to Bob, 09-07-2005 20:09:00  
Well maybe someone will read this now or in the future that has this problem and can learn from others mistakes. I had someone bring me a JD850 that had a sheared pump key,fixed it everything good to go.Couple days later he called back bitching,same problem. Well after some hard questioning I found out that while brush hogging his loader quick couplers came unhooked,he plugged them back in and I didn't know nothing about that when I saw the tractor broken down at the shop. Second time I fixed the pump I also removed that coupler.Next time it will just break the fittings and spray oil all over.

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy