Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

Flat Back to Rockshaft

Welcome Guest, Log in or Register
Author 
Bud W

04-22-2005 08:19:28




Report to Moderator

Is it easy to install a rockshaft on an unstyled A that came from the factory as a flat back?




[Log in to Reply]   [No Email]
105Diesel

04-22-2005 15:23:52




Report to Moderator
 Re: Flat Back to Rockshaft in reply to Bud W, 04-22-2005 08:19:28  
No sweat---unbolt the flat back, bolt on the rockshaft. According to a Deere document, only a half-dozen "A" or "B" tractors were ever built without a PTO, so if your tractor has a PTO, you're in business.



[Log in to Reply]  [No Email]
F-I-T

04-22-2005 12:38:52




Report to Moderator
 Re: Flat Back to Rockshaft in reply to Bud W, 04-22-2005 08:19:28  
Bud:

I do not have any personal experience on an "A", but I am doing just that on an "H" right now, so if I'm off the mark on the advice, consider how much it cost!

You'll have to remove the back cover and see if the pto bevel gear was included in the cluster. I would think it had not, so you'll need that. Then you'll need the shifter fork and the lever that goes up and exits the case near the shift lever so you can throw the pto in and out of gear. Then you'll need the PTO shaft and rear cover, which would include the oil pump and power lift (or Powr-Trol if you want to modernize it).

That should be it. The installation of the sliding gear will require that lower shaft being slid to the side so you can get it on, and there are I'm sure a few other small parts. I didn't have time to look through the parts book but if you get farther into it, someone here with more knowledge can get you better information I'm sure.

Frank

[Log in to Reply]  [No Email]
Jason Z in MO

04-22-2005 13:18:19




Report to Moderator
 Re: Flat Back to Rockshaft in reply to F-I-T, 04-22-2005 12:38:52  
Frank,

Does the term "flat back" mean it doesn't have a PTO? I thought it was just void of the power lift or powr-trol.

I have a 40 B I am restoring and I call it a flatback but it does have the powershaft.



[Log in to Reply]  [No Email]
F-I-T

04-22-2005 13:32:46




Report to Moderator
 Re: Flat Back to Rockshaft in reply to Jason Z in MO, 04-22-2005 13:18:19  
I always thought "flat-back" meant it was bare. No pto, no lift. Of course if his does have pto, then it gets a whole lots easier, doesn't it!

Good catch

Frank



[Log in to Reply]  [No Email]
Jason Z in MO

04-22-2005 13:40:29




Report to Moderator
 Re: Flat Back to Rockshaft in reply to F-I-T, 04-22-2005 13:32:46  
It would save him from having to tear down the transmission shafts to add the PTO shaft and gears! Then it would be a "bolt it on" operation.

I will have to dig out the Two Cylinder issues that covered the terminology. I know it was in there.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy