Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

Changing Pony Motor Plugs

Welcome Guest, Log in or Register
Author 
Tsmith1499

04-06-2005 20:16:06




Report to Moderator

OKay, I got my 720 home on sunday and was wondering if there is any special tool to get to the plugs on the backside of the pony motor? Also,
I have not had a chance to get a manual yet. Can someone tell me which direction the lever needs to be in to turn the fuel on or off to the pony motor? Thanks guys, Tom




[Log in to Reply]   [No Email]
tsmith1499

04-07-2005 21:40:35




Report to Moderator
 Re: Changing Pony Motor Plugs in reply to Tsmith1499, 04-06-2005 20:16:06  
Thanks guys for the help. It looks like I am going to make a stubby wrench from a long one, as I have plenty to choose from.



[Log in to Reply]  [No Email]
DW

04-07-2005 11:25:20




Report to Moderator
 Re: Changing Pony Motor Plugs in reply to Tsmith1499, 04-06-2005 20:16:06  
I built a special wrench to get mine. I cut a deep socket short, and welded a short piece of 1/4x1 stainless flat stock to the side of it at the top. It is enough to get them loose, and also tighten them back again. Saves a lot of four letter vocabulary changing those back plugs.



[Log in to Reply]  [No Email]
buickanddeere

04-07-2005 09:46:22




Report to Moderator
 Re: Changing Pony Motor Plugs in reply to Tsmith1499, 04-06-2005 20:16:06  
I've changed both the 70D and 720D starting engine "back" plugs with just an ordinary open and box wrench. Go about 1/16 turn, lift the wrench and turn 1/16th again, and again, and again. They do come out. Autolite 216 or 273 plugs.The gap is really as narrow as the book says. A clean fuel tank, fuel line, clean carb, proper float level, spark on all four plugs is vital. That and new seals on the water pump will cure 90% of all foul tempered cranking engines. Cleaning the oil drain hole in each head is required on occasion as well with a smoker. The fuel has to be shut off half a minute before shutting off the cranking engine. Or the gas will slosh into the crankcase, thinning the oil. This causes lots of smoke and ruined connecting rods. The FIT and Clooney oil pressure ignition shut off circuit is a good idea.

[Log in to Reply]  [No Email]
Dan in Ohio

04-07-2005 09:33:53




Report to Moderator
 Re: Changing Pony Motor Plugs in reply to Tsmith1499, 04-06-2005 20:16:06  
Tom, I use the same technique as 720deere only I bought a cheap wrench with a deep off set in the handle, then cut as much of the handle off as needed to be able to get in and move it easily, works for me. I'd post a picture if I was at home.



[Log in to Reply]  [No Email]
Blksmok

04-07-2005 06:39:31




Report to Moderator
 Re: Changing Pony Motor Plugs in reply to Tsmith1499, 04-06-2005 20:16:06  
Tsmith...save yourself a lot of aggravation and skinned knuckles. Pull the stater and then you can get easy access to the dash side plugs. Disconnect the battery, solenoid wires and then there are only two bolts holding the starter in place. Makes it much easier to get the plugs tight and the plugs wires reconnected. Clean the starter and check the brushes as long as you have it off the tractor.

[Log in to Reply]  [No Email]
F-I-T

04-07-2005 10:56:11




Report to Moderator
 Re: Changing Pony Motor Plugs in reply to Blksmok, 04-07-2005 06:39:31  
Blksmok:

I have never thought of that. Does it give you a lot more room? Yanking the starter isn't too mad a job on a 70D, and like you say, it can almost always benefit from at least an inspection.

Frank



[Log in to Reply]  [No Email]
Blksmok

04-07-2005 11:55:27




Report to Moderator
 Re: Changing Pony Motor Plugs in reply to F-I-T, 04-07-2005 10:56:11  
Frank..it's a little more work, but requires less total time. I'm not a very good hand/arm contortionist, but once the starter is removed ..plug replacement and wire reattachment is a two minute job.

Any progress on the SAC??

Later.



[Log in to Reply]  [No Email]
F-I-T

04-07-2005 12:23:42




Report to Moderator
 Re: Changing Pony Motor Plugs in reply to Blksmok, 04-07-2005 11:55:27  
SAC?



[Log in to Reply]  [No Email]
Blksmok

04-07-2005 13:01:58




Report to Moderator
 Re: Changing Pony Motor Plugs in reply to F-I-T, 04-07-2005 12:23:42  
Frank .... S.A.C. - Spousal Avoidance Center (aka barn/workshop)



[Log in to Reply]  [No Email]
F-I-T

04-07-2005 13:13:44




Report to Moderator
 Re: Changing Pony Motor Plugs in reply to Blksmok, 04-07-2005 13:01:58  
Ahhhhh !

Permit has been approved as of last week, so next is the prepping of the lot to strip off the top soil and then haul in the fill and pack it, then the crew arrives. I need to check in with the Morton rep, but he said a couple weeks ago maybe start by the eom APril. He thought two weeks to complete.

Then the concrete and electrical/plumbing/lighting/etc.



[Log in to Reply]  [No Email]
Blksmok

04-07-2005 13:24:20




Report to Moderator
 Re: Changing Pony Motor Plugs in reply to F-I-T, 04-07-2005 13:13:44  
That sounds like good progress. Should be a fun summer finishing off the inside and setting up the workshop. My bldg. plans are being delayed a little bit by a thing called AMT (alternative minimum tax) that Uncle Sam wants next week. Makes you proud to be an American!!! Later



[Log in to Reply]  [No Email]
720Deere

04-07-2005 05:22:27




Report to Moderator
 Re: Changing Pony Motor Plugs in reply to Tsmith1499, 04-06-2005 20:16:06  
Changing the rear pony motor plugs requires a mixture of wrenches and maybe even your favorite high test beverage. I have a set of stubby wrenches that work fairly well. With the stubby, you can get the box end over the plug and inch it out a little at a time. If you are a good enough contortionist, you can even use a socket on one of them. It doesn't take much with the wrench. Once you get them broke loose, you can usually turn them out with your fingers.

[Log in to Reply]  [No Email]
WeirdDeere

04-06-2005 23:39:27




Report to Moderator
 Re: Changing Pony Motor Plugs in reply to Tsmith1499, 04-06-2005 20:16:06  
The fuel shutoff is counterclockwise to open, clockwise to close. Or as I like to say:

Righty tighty, lefty loosy.

Can't help with the plugs. My 80 has barely enough room to change them. I've heard your 720 is even worse. Ugh.

Brandon
My Industrial John Deere website
John Deere Diesels
The LaGrange Engine Club

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy