Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

'37 A leaking oil on flywheel side of crankshaft

Welcome Guest, Log in or Register
Author 
DE

04-06-2005 19:40:20




Report to Moderator

Have a "37 A that leaks oil on the flywheel side of the crankshaft. Took the flywheel off and cover over the oil seal. It looks like the cork seal around the crankshaft is where the leak is. Can this crok seal be replaced or does something else work better? Thanks




[Log in to Reply]   [No Email]
Skyhaw Greg

04-07-2005 18:02:20




Report to Moderator
 Re: '37 A leaking oil on flywheel side of cranksha in reply to DE, 04-06-2005 19:40:20  
DE - I replaced the cork seal on my B about 2 years ago. Used the standard cork from the JD dealer. Not a drop since then. Make certain that you use a feeler gauge to ensure clearance between the casing and the crankshaft, or you will continue to leak. If you have any questions about what I just said, feel free to e-mail me. Greg

[email protected]



[Log in to Reply]  [No Email]
JGC

04-07-2005 14:28:25




Report to Moderator
 Re: '37 A leaking oil on flywheel side of cranksha in reply to DE, 04-06-2005 19:40:20  
Someone suggested machining a groove in the flywheel spacer ring and adding an o'ring along with the factory seal because the cork seals tend to dry out from sitting. We did this and it worked very well. Our oil pressure is right at the very top of the gauge and we only get occasional small leaks at the bearing on the flywheel end.

JGC



[Log in to Reply]  [No Email]
F-I-T

04-07-2005 08:13:14




Report to Moderator
 Re: '37 A leaking oil on flywheel side of cranksha in reply to DE, 04-06-2005 19:40:20  
Be sure the the crankcase ventilation. If the crankcase builds up any extra pressure it can push out the cork seal as well.

I know this because while my "H" was running I though it would tricky to blow a little compressed air into the vent pipe and it blew oil out the crank seal area which hit the turning flywheel and it slung it all the heck over@!

I love this stuff!@#!

Frank



[Log in to Reply]  [No Email]
John T

04-06-2005 21:04:17




Report to Moderator
 Re: '37 A leaking oil on flywheel side of cranksha in reply to DE, 04-06-2005 19:40:20  
DE, I have sucessfully used the cork seals I got from Mother Deere, but we soaked them in hot oil quite a bit to soften them prior to installation. Dont forget to buff/polish the crank where that seal rides,,,,, ,get the lil tip on the inner flywheel into the open notch in the oil slinger (in that D shaped bearing/seal housing) when reinstalling the flywheel,,,,, ,,,get the flywheel back on the correct spline in time,,,,, ,take the flywheel in all the way to 0.010 to 0.015 of end play.

Good luck

John T

[Log in to Reply]  [No Email]
Larry806

04-06-2005 19:50:34




Report to Moderator
 Re: '37 A leaking oil on flywheel side of cranksha in reply to DE, 04-06-2005 19:40:20  
Your dealer should have or can get it. Most of the time I find the old ones are hard and brittle. I think you'll find that to be on this one. Ps don't forget to order the gasket too



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy