Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

4010 lights and pto shaft

Welcome Guest, Log in or Register
Author 
Wolfie

03-11-2005 07:30:46




Report to Moderator

I have a 4010 standard diecel lights mounted on the fenders. It has the standard 24 volt system still in place. My question is when sitting on the tractor the left light is not very bright. I thought it may be the bulb so I bought a new one and it still is the same. The right one seems to be very bright and the rear light is also brighter What could be my problem? Also is the 1000 rpm shaft shorter in length than the 640 shaft? I bought the 1000 rpm shaft on e-bay they said it was for a 4010 but like I said it is about an inch shorter in length than the 640.

Wolfie

[Log in to Reply]   [No Email]
buickanddeere

03-12-2005 07:16:56




Report to Moderator
 Re: 4010 lights and pto shaft in reply to Wolfie, 03-11-2005 07:30:46  
The system is best balanced if the A & B side both have the same number and size of lights. Idealy that ground wire just handles current for the fuel gauge. Or to get you home to the shop for a new light should one light fail. Keep the charge voltage set up to at least 27.6 to 28.4V measured back at the batteries at fast idle.



[Log in to Reply]  [No Email]
Steve,Ga

03-12-2005 01:22:21




Report to Moderator
 Re: 4010 lights and pto shaft in reply to Wolfie, 03-11-2005 07:30:46  
The 1000 shaft will have a hole in center of base.when you remove 540 the spring loaded rod will come back.this engages 1000 rpm.Without getting to long winded,get a manual!!I have done the repair on the little pin that will shear.when you put the 540 back on BE SURE to rock tractor till you fell the shaft sliding onto shaft dont force.the 1000 shaft is shorter best I remember,Steve



[Log in to Reply]  [No Email]
jd68

03-11-2005 08:56:59




Report to Moderator
 Re: 4010 lights and pto shaft in reply to Wolfie, 03-11-2005 07:30:46  
the lights sound like a poor ground. the pto shafts are diffrent lenghts I don"t remember witch is the long or short one, but i"m sure they are diffrent.



[Log in to Reply]  [No Email]
Bob

03-11-2005 08:51:09




Report to Moderator
 Re: 4010 lights and pto shaft in reply to Wolfie, 03-11-2005 07:30:46  
Not sure exactly what you have with the PTO.

The tractor has a 24 Volt electrical system with the center grounded to the chassis, giving (+) 12 Volts to half of the lights and (-) 12 Volts to the other half.

The symptoms you describe indicate this ground connection to the chassis is missing, making 1/2 of the lights get too much voltage, and the other 1/2 not get enough voltage.

Look for a wire (possibly with a fuseholder in-line) that should be connected from the battery cable that jumpers the 2 batteries together, to the tractor chassis.

Wear safety googles when woking around the batteries, as a spark can cause a NASTY battery explosion.

[Log in to Reply]  [No Email]
Wolfie

03-11-2005 09:22:31




Report to Moderator
 Re:BoB 4010 lights and pto shaft in reply to Bob, 03-11-2005 08:51:09  
Is this wire with the fuse under the platform ? Aso would the 24 volt system still fuction if the wire is missing like you stated?

Wolfie



[Log in to Reply]  [No Email]
Bob

03-11-2005 09:57:21




Report to Moderator
 Re:BoB 4010 lights and pto shaft in reply to Wolfie, 03-11-2005 09:22:31  
That sounds like the fuse. The correct replacement is a slow-blo fuse. Some use a length of fusible link.

The 24 Volt charging and starting system WILL work with the center ground missing. The lights, and fuel gauge will be most affected.



[Log in to Reply]  [No Email]
Wolfie

03-11-2005 10:13:57




Report to Moderator
 Re:BOB FUSE 4010 light and pto in reply to Bob, 03-11-2005 09:57:21  
Bob is the fuse in the line with the cable? I really do not know what to look for here. I have the service Manual I will look for the connecting cable. The fuel gage sometimes go's wacky shows empty when full. Then next you start the tractor it will work fine. The cable could be missing. I bought this tractor about a year ago but have not had to use it at night yet. The one batery is on the right side by the platform in a box and the other one is on the left side in a box. Would this be a long cable connecting the two?

Wolfie

[Log in to Reply]  [No Email]
Bob

03-11-2005 10:23:20




Report to Moderator
 Re:BOB FUSE 4010 light and pto in reply to Wolfie, 03-11-2005 10:13:57  
The chassis ground wire is a SMALL wire that could be connected to either end of the LARGE cable you mention that crosses over the tractor, fom one battery to the other. What's your S.N.?



[Log in to Reply]  [No Email]
Wolfie

03-11-2005 10:35:23




Report to Moderator
 Re:BOB Cable 4010 light and pto in reply to Bob, 03-11-2005 10:23:20  
Bob I have the NO. at home but it's a 1963 diecel standard or some say wheatland big rounded fenders no 3 point. I did notice a smaller cable conected to the tractor frame. If this is the one we are talking about it still is on the tractor.

Wolfie



[Log in to Reply]  [No Email]
Bob

03-11-2005 11:07:28




Report to Moderator
 Re:BOB Cable 4010 light and pto in reply to Wolfie, 03-11-2005 10:35:23  
Just to clarify...

There were different setups on the various 4010's and 4020's for the centerpoint of the 24 Volt ground to chassis. Many of these tractors have had their original 24 Volt system changed or modified since they were new, so it's always hard to tell "over the 'net" exactly what you're dealing with.

Some had 1 braided battery cable from each battery connected to the tractor chassis. Others had a cross-over cable from one battery to the other, with a small jumper wire, sometimes fused, to chassis ground. These changes DO NOT affect how the 24 Volt starting and charging systems work, only the details of the dual 12 Volt system.

If you DO NOT have the individual ground straps from each battery to ground, and DO have the cross-over cable between the batteries, you DO NEED the little ground wire, and it sounds like you've found the remains of one. There are certain electrical shorts that can happen that make it a good idea to have a slo-blo fuse in that lttle lead, but many of these tractors do not.

[Log in to Reply]  [No Email]
Wolfie

03-11-2005 11:21:53




Report to Moderator
 Re:BOB Cable 4010 light and pto in reply to Bob, 03-11-2005 11:07:28  
Ok thanks Bob. I will take a good look and see what is going on.

Wolfie



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy