Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

Connecting rod nuts/cotter pins

Welcome Guest, Log in or Register
Author 
Dave in SV

03-05-2005 17:29:15




Report to Moderator

On my '49 A, with the connecting rod nuts tight, the hole for the cotter pin is too far away, thus the cotter pins do not nestle into the notches of the nuts. In fact, the nuts would have to back out about two or three threads before the tops of the notches would even touch the cotter pins.

Any suggestions for a remedy? Washers/spacers under the nuts?




[Log in to Reply]   [No Email]
Dave in SV

03-06-2005 08:08:58




Report to Moderator
 Re: Connecting rod nuts/cotter pins in reply to Dave in SV, 03-05-2005 17:29:15  
Fellas... there does not appear to be any shims between the rods and the caps, so the exposed bolt length beyond the nuts is at max... and the cotter pin holes are a mile away from the notches. Is this designed so as to accommodate something in excess of .250 in variable due to bearing wear/resizing? That's a lot of spread!

I like Lynard's idea.



[Log in to Reply]  [No Email]
F-I-T

03-06-2005 09:32:30




Report to Moderator
 Re: Connecting rod nuts/cotter pins in reply to Dave in SV, 03-06-2005 08:08:58  
Dave:

Do you have insert type rod bearings or babbit bearings? The babbit would use a shim pack that, when the bearings are new and at their thickest state, would be near 1/4".

You know if you have a lot of threads sticking out you can use the time honored method of using a lock nut on the rod nut, but it sounds as though you might have a mix of hardware. The drilled bolts were for sure the older types that used cotter pines, typically for the babbit bearing rods.

You know, the old castellated nus were pretty tall. Any chance someone substituted shorter castle nuts on you? That would explain a lot.

Frank

[Log in to Reply]  [No Email]
Dave in SV

03-06-2005 16:45:31




Report to Moderator
 Re: Connecting rod nuts/cotter pins in reply to F-I-T, 03-06-2005 09:32:30  
Great thought... about whether the castle nuts are shorties or not. However, these nuts are (in my limited experience) quite tall. The first thing I thought when I saw them was... "Geeze, these nuts are tall".

Lynard suggested self-locking nuts as are used in another model tractor. Would you do that? It makes sense to me, and would settle the issue.



[Log in to Reply]  [No Email]
F-I-T

03-06-2005 17:32:44




Report to Moderator
 Re: Connecting rod nuts/cotter pins in reply to Dave in SV, 03-06-2005 16:45:31  
Those are called Marsden nuts. I'm not sure if they will work with the old style bolt threads or not. I'm not aware of a reason they would not work, but I've only ever got them by buying a new rod bolts.

I would just use a washer. The shim packs had brass shims in them. so I'm confident that any decent flat washer once torqued down would safely take up the slack.

Frank



[Log in to Reply]  [No Email]
Lynard

03-06-2005 06:31:42




Report to Moderator
 Re: Connecting rod nuts/cotter pins in reply to Dave in SV, 03-05-2005 17:29:15  
Dave Another method would to use the nuts from a 620 as they do not use cotters. They use a slotted nut and torque to the same value as an A. Lynn



[Log in to Reply]  [No Email]
Dave in SV

03-11-2005 16:16:35




Report to Moderator
 Re: Connecting rod nuts/cotter pins in reply to Lynard, 03-06-2005 06:31:42  
Just picked up a set of nuts for a 620... and they work great in my A. Thanks for the great idea!!!



[Log in to Reply]  [No Email]
F-i-T

03-06-2005 07:10:16




Report to Moderator
 Re: Connecting rod nuts/cotter pins in reply to Lynard, 03-06-2005 06:31:42  
The replacement bolts are the non-cotter pin types, known as Marsden nuts.

I'm still wondering how much babbit is left on those rods.



[Log in to Reply]  [No Email]
Lynard

03-06-2005 15:25:08




Report to Moderator
 Re: Connecting rod nuts/cotter pins in reply to F-i-T, 03-06-2005 07:10:16  
F-i-T I did not know that about those nuts. I guess I ain't too old to learn something. If they are no shims on the rods better get out the mike and do some checking on the crank also. Lynn



[Log in to Reply]  [No Email]
Steve,Ga

03-06-2005 03:34:54




Report to Moderator
 Re: Connecting rod nuts/cotter pins in reply to Dave in SV, 03-05-2005 17:29:15  
That cotter pin is not going to hold the torque,if its in the notch let it go.I always felt it would keep the bolt out of the crankcase.Steve



[Log in to Reply]  [No Email]
F-I-T

03-05-2005 17:45:36




Report to Moderator
 Re: Connecting rod nuts/cotter pins in reply to Dave in SV, 03-05-2005 17:29:15  
Dave:

Sounds like there might be quite a bit of wear in those rod bearings. You can use some flat washers and that would work. Hard flat washers might be better, but I'm not sure that that would be necessary. Lowe's and Home Depot carry them in their specialty hardware boxes.

Frank



[Log in to Reply]  [No Email]
Pat Browning

03-05-2005 17:52:25




Report to Moderator
 Re: Connecting rod nuts/cotter pins in reply to F-I-T, 03-05-2005 17:45:36  
Hold it just a Minute! Never, ever put any fasteners from Home Depot into the crankcase of a John Deere!! Go to a fastener place in your town and purchase some washers the body of a lock washer but they are flat and not slit,--Grade 5 hardness is what to use. (PatB)



[Log in to Reply]  [No Email]
F-I-T

03-05-2005 18:47:49




Report to Moderator
 Re: Connecting rod nuts/cotter pins in reply to Pat Browning, 03-05-2005 17:52:25  
Look Pat. It's a flat washer between hardened surfaces. Just how much do you think is gonna squish out when it's probably at least 32 RC?

I stand by my advice. I also mentioned the hardened versions available. It's for a spacer.

Frank



[Log in to Reply]  [No Email]
fixerupper

03-05-2005 19:36:39




Report to Moderator
 Re: Connecting rod nuts/cotter pins in reply to F-I-T, 03-05-2005 18:47:49  
All engines that use washers under the rod bolts use hard ones. If the soft ones compress even a few thousanths of an inch over time, that might be enough to loosen the bearing beyond the proper running clearance.



[Log in to Reply]  [No Email]
F-I-T

03-06-2005 07:06:56




Report to Moderator
 Re: Connecting rod nuts/cotter pins in reply to fixerupper, 03-05-2005 19:36:39  
Yeah? Well on an "A" JD, they also use brass shims on the rod caps.

Which do you think will compress first? Brass or an unhardebed steel washer?

Crimeny, the torque is only 75 lbs.



[Log in to Reply]  [No Email]
gusc

03-06-2005 18:50:58




Report to Moderator
 Re: Connecting rod nuts/cotter pins in reply to F-I-T, 03-06-2005 07:06:56  
FIT,

I agree, this is not the space shuttle. 100lb-ft is not going to compress any washer very much!!

What kind of precision do you suppose JD used in 1949??



[Log in to Reply]  [No Email]
Dave in SV

03-06-2005 18:38:19




Report to Moderator
 Re: Connecting rod nuts/cotter pins in reply to F-I-T, 03-06-2005 07:06:56  
The I&T JD-4 Manual, paragraph 87, says to torque rod bolts to 100 ft.-lbs. Can you clarify which value (100 or 75) is correct?



[Log in to Reply]  [No Email]
F-I-T

03-06-2005 20:05:22




Report to Moderator
 Re: Connecting rod nuts/cotter pins in reply to Dave in SV, 03-06-2005 18:38:19  
Go with your manual. I was just speaking to the fact that the torque in compressive stress is insignificant to that that a washer can withstand.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy