Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

2010 engine replacement

Welcome Guest, Log in or Register
Author 
chris meredith

02-05-2005 14:15:48




Report to Moderator

i have frend that has a 2010 gas motor cast number t 12082-t ser 10685 and he bouth a motor out of a 45 combine witha cast number of t 12181t and he says i will not fit at all does it sposse to fit is this engine one that will not fit the 2010 i have chage a engine out of a 1010 from a 45 combine it had the excact same cast number on the block just allot biger engine will the engine out of a 45 square back combine fit the 2010 it is the same thing i put in a 1010 will it fit

[Log in to Reply]   [No Email]
jdemaris

02-05-2005 19:33:48




Report to Moderator
 Re: 2010 engine replacement in reply to chris meredith, 02-05-2005 14:15:48  
I don't fully understand your post. A 2010 gas engine is the same size as a 1010 diesel as far as bore and stroke goes. Physically, 1010 and 2010 motors, gas or diesel are the same dimensions on the outside. I'm not sure about the crankshaft ends and matching flywheels. Do you have a 2010 engine that you want to put into a 1010? Or, have you put a combine engine into your 1010? I've been curious about how easy it is to mix the combines engines, 1010s, and 2010s between different crawlers and wheel tractors. As far a bolt pattern goes, of the 1010/2010 series engine block, I don't think they match up to the next generation engines, like the 135 and 180 gas, or 152 and 202 diesels as used in 2510s, 1020s, 350 and 450 crawlers. I don't know if perhaps they have the old two cylinder bolt pattern, or one all their own. 1010 gas engine (115 c.i.) is the just about the same cubic inch size as the 420 and 440 two cylinder (113 c.i.). The 1010/2010 series certainly looked as if Deere was using up a bunch of left over parts. Just had some discussion with RAB and the possibilities of putting a 2010 sleeve deck in a 1010 block, or perhaps using a 2010 diesel block (with the extra main bearings) but converting it to gas by using gas pistons, head, etc. That all being said, you can get good use out of any of the 1010/2010 engines if set-up and cared for properly. Main problem is parts availability and the lack of updates on these engines. They are all single o-ring sleeve sealing, which is not great. Deere made upgrade kits for all their later single o-ring engines, but not for the 1010/2010 series. Also, many early engine parts were obsolete and no longer available by the mid-70s.

[Log in to Reply]  [No Email]
T213R

02-05-2005 15:08:59




Report to Moderator
 Re: 2010 engine replacement in reply to chris meredith, 02-05-2005 14:15:48  
I don't think that there is much of anything which would be a good, bolt in replacement engine for a 2010! In fact, I think you'd have better luck trying to shoehorn or jury rig some other brand of engine into it. If you had almost anything, with four cylinders and about 150-160cid, with enough work, you might be able to get something to adapt! The John deere combine engines you mention don't seem to me to be enough of an improvement to be worth the effort!

[Log in to Reply]  [No Email]
buickanddeere

02-05-2005 17:22:08




Report to Moderator
 Re: 2010 engine replacement in reply to T213R, 02-05-2005 15:08:59  
Did the later engines like the 239 share the same bolt patterns anywhere as a the sleeve/deck 1010 and 2010 engines?



[Log in to Reply]  [No Email]
HTR

02-05-2005 20:35:53




Report to Moderator
 Re: 2010 engine replacement in reply to buickanddeere, 02-05-2005 17:22:08  
No, the 300 series 202, 219, 239, 329,etc engines are a entirely different bolt pattern. The 200 series engine,92,115, 145, 248, etc. share the bolt pattern with the Dubuque two cylinder tractors.

The 300 series,239,etc. used different flywheel housings (back plates) on the engine to adapt for different equipment. Flywheel housings for Dubuque 1020, 2020, 2550,etc., SAE four housings for combines, backhoes, ind. equipment and such. No flywheel housings that would bolt to the 2010,were made.

The engine of the 2010 is the frame of the tractor. Side rails were optional. Even if you could adapt the back of the engine to bolt, it would take a lot of afro engineering to bolt the front of the engine to the axle housing.

There was nothing wrong with the 145, gas engines. They did alot of work in combines, swathers, and other equip. from 1957-1964. The deck plate didn't give any more problems than any other engines. The 1957 to early 1960, 145 engines were parent bore, if you don't like the deck plate.

[Log in to Reply]  [No Email]
chris meredith

02-05-2005 19:06:24




Report to Moderator
 Re: 2010 engine replacement in reply to buickanddeere, 02-05-2005 17:22:08  
yes the both moter he has is a sleve deck in them he was thinking that his sleve deck out of is 2010 might work in my old 1010 block does anyone no if that would work thanks chris



[Log in to Reply]  [No Email]
jdemaris

02-06-2005 10:54:03




Report to Moderator
 Re: 2010 engine replacement in reply to chris meredith, 02-05-2005 19:06:24  
2010 gas engine deck should fit a 1010 diesel engine since they are the same bore and stroke. But, otherwise, the decks are different diameters and won't fit. I've heard rumours about getting the 1010 gas engine block machined to accept the bigger bore decks, but never actually seen it one.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy