Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

4020 Injectors

Welcome Guest, Log in or Register
Author 
Wide Open

02-01-2005 17:32:13




Report to Moderator

Hi there JD guys, I am a man of the other green, but I managed to somehow pickup a 1964 4020, runs ok, but injectors are pretty tired. I was just wonderin if you could give me a ballpark figure for the cost of new injectors? Or, can they be rebuilt, and at what cost? Thanks guys. -Wide Open




[Log in to Reply]   [No Email]
JD Jack

02-02-2005 21:27:10




Report to Moderator
 Re: 4020 Injectors in reply to Wide Open, 02-01-2005 17:32:13  
Just bought some rebuilt ones.... $125 a piece! I am not sure where these came from, b/c my mechanic found them. They are tought to come by, and no new ones are available.



[Log in to Reply]  [No Email]
4020dt

02-02-2005 04:22:47




Report to Moderator
 Re: 4020 Injectors in reply to Wide Open, 02-01-2005 17:32:13  
If its a 1964 it will have the big injectors , I don't think they are available new anymore nor are parts for them from Deere , anyway if they were they are too expensive anyway . They can be rebuilt , had mine done a few yeas ago . There were , at least back then , rebuilt parts for . Find a GOOD diesel shop , they are hard to find , I know . My tips were ok but I had rebuilt valves put in , don't remember the exact $$ but I think it was around $75/injector to have them all rebuilt and set to proper pressure . I have two '64 , a 3020 and 4020 with the big injectors . I found a set (6) of them supposedly rebuilt on EBAY a year ago or so , haven't used them or checked them out yet though . If they are good they were a buy for $25/piece .

[Log in to Reply]  [No Email]
jdemaris

02-01-2005 20:14:15




Report to Moderator
 Re: 4020 Injectors in reply to Wide Open, 02-01-2005 17:32:13  
Than can be "rebuilt", but it's probably not worth the bother. We used to send them out, get them done, and charge $20 apiece instead of the $45 for new ones (that's back in 1989). The rebuilt pencil injectors wouldn't last anywhere near as long as the new ones. Basically, you'd use injector nozzle cleaning wires to clean the orifices, then clean and lap the needle and seat, and then put on a pop tester and set the pressure, check for nozzle dribble, etc. Main issue is that the tips can't be replaced on the pencil injectors - all you can do is clean them up and reseat them a bit. Most of the injection shops that I know of, nowadays, don't want to service injectors at all - except for complete tip or nozzle replacement. I just bought new CAV replacement nozzles for my 6.2 litre Chevy V-8 - $11 bucks apiece. I wish I could buy tractor nozzles that cheap!

[Log in to Reply]  [No Email]
msb

02-01-2005 20:25:23




Report to Moderator
 Re: 4020 Injectors in reply to jdemaris, 02-01-2005 20:14:15  
But he said a 1964 model.It would have the large nozzles,not the pencil type.The large nozzles can be rebuilt and should be a lot cheaper than new ones.



[Log in to Reply]  [No Email]
jdemaris

02-02-2005 05:29:22




Report to Moderator
 Re: 4020 Injectors in reply to msb, 02-01-2005 20:25:23  
As usual, I didn't read closely enough and didn't notice the year. That being said, most of
the injector shops I know of don't want to bother with repairing old nozzles anymore. I
guess if you have one that new parts cannot be gotten for - it'll be a different story. We
went through that in the early 60s with the 1010 and 2010 diesels. The early injection
nozzles were discontinued - we couldn't get them anywhere. Deere offered complete new
injectors for repair which was expensive. So, standard procedure was to take the nozzles
apart, clean the orifices, lap the parts, and reset. Worked okay, but not as good as new. Once the metal seats get worn, lapping won't bring them back. If someone knows of a good diesel shop that is actually willing to attempt repair of
injectors, I'd like the address. I got lazy over the years and started sending mine out. But,
I'm kind of disgusted with it and am going to start doing it myself again. Last two sets of
injectors I sent out did not go well as I see it. I had a IH B275, ran and started fine, but I
sent injectors out to get tested and cleaned up if necessary - came back with all new tips
and a bill of $295 for four injectors. The place put new (and expensive nozzles) on them
with getting back to me first. Then, I had my Allis Chalmers HD4 apart - again, four
cylinders and large injectors with replaceable tips. I sent them to a different place, and
also asked to have them checked, and/or cleaned up - and if there was a large expense
involved to contact me first. I also requested that all the old parts be returned to me. Well, they came back UPS - COD - with no one contacting me in the interim. The bill
was $272 with no explanation and none of my old parts returned. Now, I understand
parts can be expensive, but I get the feeling that, at least the places I'm dealing with, don't
even attempt to fix the old nozzles. If the new parts were as cheap as for my G.M diesels
- I'd understand - but when they're

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy