Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

Float Ride seat whoopin my butt

Welcome Guest, Log in or Register
Author 
Soldier Tom

11-28-2004 14:43:06




Report to Moderator

Anyone with advise to offer, Im all ears. The seat torsion springs were a piece of cake compared to removing the drive pins from the cross shafts. Ive got the manual, I took a bigol hammer and punch just like it said to, and suceeded in doing nothing at all to drive out the drive pin (or un-drive-able pin apparently) I have it still soaking in PB blaster. These need to come out so I can replace the rest of the bearnings, right? I am going to have to break down and get some serious heat ain't I? I been trying the little propain torch, and it seems to do nothing much. Any advise appreciated, I hate to throw in the towl.
~Walk in peace~
Soldier Tom

[Log in to Reply]   [No Email]
Mike M

11-28-2004 15:35:36




Report to Moderator
 Re: Float Ride seat whoopin my butt in reply to Soldier Tom, 11-28-2004 14:43:06  
Are you talking about the pins in the 4 corners of the seat frame ? I use an air hammer with a flat faced punch and push them right out.To install I use a large c-clamp and squeeze them right in place.



[Log in to Reply]  [No Email]
Dan in Ohio

11-28-2004 15:32:20




Report to Moderator
 Re: Float Ride seat whoopin my butt in reply to Soldier Tom, 11-28-2004 14:43:06  
Soldier Tom,

I used an air hammer/chisel and had mine apart in a few minutes (after beating on it with a 3lbs. hammer by hand for an hour). You'll be as suprised as I was.



[Log in to Reply]  [No Email]
F-I-T

11-28-2004 15:54:48




Report to Moderator
 Re: Float Ride seat whoopin my butt in reply to Dan in Ohio, 11-28-2004 15:32:20  
I say ditto to those air riveters with a flat punch. I walked two rusted pinion bolts out of my F1500 wheels and everyone watching was amazed.

Frank



[Log in to Reply]  [No Email]
Soldier Tom

11-29-2004 16:51:28




Report to Moderator
 Re: Float Ride seat whoopin my butt in reply to F-I-T, 11-28-2004 15:54:48  
Air hammer it will be then, I just gotta find one now. I think I can find one here on post at the auto care self help center. Never would'a thunk a that. Thanks all!!!
I will let you know what happens!
~Walk in peace~
Soldier Tom



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy