Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

50 pto clutch slipping

Welcome Guest, Log in or Register
Author 
Jdtractorboy

10-16-2004 19:32:10




Report to Moderator

Howdy,

as I have stated on here before, this spring I put all new friction disks and seals in my 1955 "50." However, even if i adjust the clutch up so tight it wil almost be impossible to pull into engagement, it still slips horribly.

What am I not doing? My frind and I will be pulling it back off the tractor tomorow. What should we look for to be out of adjustment? Also, how do yall engage/disengage the clutch on the bench. Deere had me put 3 new springs in and it is DIFFICULT to lock/unlock now!

Finally, anyone who is really familiar with these, could you send or put your phone number on here so i can call with questions during the tear down/inspection.

Thanks

Chuck

[Log in to Reply]   [No Email]
chuck mcdonald

10-18-2004 21:24:31




Report to Moderator
 Re: 50 pto clutch slipping in reply to Jdtractorboy, 10-16-2004 19:32:10  
hi,

thanks for all the replies. How do you get to to the small springs that hold the clutches together? I replaced the three springs, but i guess i should also replace these others. Anyone have a picture of how to get to it?

I dont have my camera up as school, so i cant take pics. Sorry.



[Log in to Reply]  [No Email]
John Van Valkenburgh

10-17-2004 20:52:16




Report to Moderator
 Re: 50 pto clutch slipping in reply to Jdtractorboy, 10-16-2004 19:32:10  
Chuck,

I don't claim to be an expert but I did have my PTO clutch apart this summer for cleaning when I resealed the PTO pump and rockshaft assy. I also have the John Deere manual and parts book, which should pretty much cover everything. I recall there is an adjustment you need to do with a feeler gauge.

Yes the clutch is a bit difficult to snap in/out when its on the bench. I used a couple of big screwdrivers.

Having said all this, if you think your PTO clutch is okay, or at least tightly engaged then you may have a broken gear or broken pin somewhere in the system that has enough of a friction hold to spin the PTO shaft a little but can't take any load.

I'll have to go have a look at the parts book to see if there are any suspecious areas you may want to look at.

I can scan and fax the parts blowup if you need it. I unhid my email if you need to contact me.

Best of luck,
John
1953 Model 50

[Log in to Reply]  [No Email]
Tyler-MO

10-17-2004 19:19:30




Report to Moderator
 Re: 50 pto clutch slipping in reply to Jdtractorboy, 10-16-2004 19:32:10  
I have been through the power shaft clutch in my 520 (which is similar to the 50) and am also in the process of putting the powershaft clutch back together on a 50 that belongs to a friend of mine. It sounds like maybe you should have replaced the 8 or 9 springs that actually give the pressure on the discs. You said that you replaced 3 springs (I assume that these were the small ones that keep the end (thick) metal plates w/facing on only one side apart when the clutch is disengaged.

Also, was the part that the 3 balls ride on very worn. I have heard that this can make the clutched weak even when engaged. This really doesn't make sense to me. As the other fellow said, if you could get ahold of a digital camera and take pictures of the clutch when you disassemble it would make this diagnosis much easier.

Let me know if you with what help you need. Tyler in Missouri
(I'm not an expert, just a 21 year old college student that knows too much about these tractors that are 2 or 3 times older than himself to be dangerous)

[Log in to Reply]  [No Email]
Mike M

10-18-2004 06:24:56




Report to Moderator
 Re: 50 pto clutch slipping in reply to Tyler-MO, 10-17-2004 19:19:30  
I think that if that part that holds the three balls is worn bad that the balls could be tight in one spot and then loosen up if they go into a worn spot.



[Log in to Reply]  [No Email]
Mike M

10-17-2004 18:55:12




Report to Moderator
 Re: 50 pto clutch slipping in reply to Jdtractorboy, 10-16-2004 19:32:10  
Can you post any pictures ?



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy