Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

Carb bolts seized in manifold

Welcome Guest, Log in or Register
Author 
STEVE JO

08-01-2004 16:33:52




Report to Moderator

I am taking the




[Log in to Reply]   [No Email]
Jon C -Florida

08-01-2004 17:13:00




Report to Moderator
 Re: Carb bolts seized in manifold in reply to STEVE JO, 08-01-2004 16:33:52  
Steve -
Your post did not come through, but from the title, I'm assuming you are trying to get bolts or studs out from a manifold.

If my guess is correct, I have found that the best method to get them out is to take the manifold off, and then heat the manifold around the stud cherry red. Then assuming some if the stud is sticking out, put on a baby pipe wrench or good vise grips and apply some torque.

Do not try to loosen the stud until the manifold is cherry red. But after its cherry red, they should squeek out.

(If this was not your post...never mind.)

[Log in to Reply]  [No Email]
STEVE CAN

08-01-2004 17:29:43




Report to Moderator
 Re: Carb bolts seized in manifold in reply to Jon C -Florida, 08-01-2004 17:13:00  
Sorry the post didn't work , What Iam trying to do is take the carb off my JD "60" I have heated the bolts red hot and let cool, with no luck. Could I apply heat to the manifold (I don't want to remove the manifold) Would this do damage to it if I left it on? Any other ideas?



[Log in to Reply]  [No Email]
Jon C -Florida

08-01-2004 18:19:21




Report to Moderator
 Re: Carb bolts seized in manifold in reply to STEVE CAN, 08-01-2004 17:29:43  
Steve - Is the carb still on the manifold?

If the bolts have sheared off and the carb is off, then yes, you can apply heat to the manifold, around the studs. It wont hurt the manifold....just dont add oxygen or cut it.
(Make sure the gas tank , lines etc. is well insulated from the heat). Try to keep the heat away from the studs, but around them on the cast. Don't let the manifold cool after its heated or it wont work....it has to be cherry red.

If you don't like this idea, and again if the carb is off, use a wire feed welder to weld on a flat washer to the remaining stud, in the center of the washer. Then weld a nut to the washer. Then try backing out the home made bolt from the manifold. The heat of welding combined with the torque applied from a standard wrench should do it.

You could also try penetrating fluid, and left hand drill bits, but it will be difficult to get to with the manifold on the tractor. "Easy outs" are worthless, in my opinion.

My best luck has been the heat method.

[Log in to Reply]  [No Email]
STEVE CAN

08-01-2004 18:32:12




Report to Moderator
 Re: Carb bolts seized in manifold in reply to Jon C -Florida, 08-01-2004 18:19:21  
Jon, the carb is still on. I am afraid of breaking the stud bolts off that hold the carb to the manifold. It is the two top bolts . I will try heating the manifold,and try turning them when it is hot. I was afraid of cracking it



[Log in to Reply]  [No Email]
Jon C -Florida

08-01-2004 18:58:44




Report to Moderator
 Re: Carb bolts seized in manifold in reply to STEVE CAN, 08-01-2004 18:32:12  
Well I can't blame you for not wanting to hurt the manifold. Although I have done it successfully without any problems.

Here is another idea to try. If you have an impact wrench that is adjustable, try one of the slowest settings and tap on the side of the manifold where the bolt goes in with a ball peen hammer at the same time (withoug breaking the casting!) I'll take a look at my 60 carb/manifold in the shed tomorrow to see what your up against. If you cant get a pneumatic or electric impact wrench in there, maybe a manual one will work. Soak the area with penetrating oil tonight...as I'm sure you already have.

The shock may break the bolts loose.

[Log in to Reply]  [No Email]
STEVE CAN

08-01-2004 20:00:18




Report to Moderator
 Re: Carb bolts seized in manifold in reply to Jon C -Florida, 08-01-2004 18:58:44  
Thanks Jon, Will try the heat trick in the morning.



[Log in to Reply]  [No Email]
Jon C -Florida

08-02-2004 04:34:27




Report to Moderator
 Re: Carb bolts seized in manifold in reply to STEVE CAN, 08-01-2004 20:00:18  
I just walked out to look at my 60 carb....and now see that you can"t get an impact wrench in there.

Looks like the one on the right side may be slightly easier to heat than the "outside" left one.

Maybe try using a standard box wrench while tapping directly on the head of the cap screw with a drift pin? (Need four hands or a friend to help.)



[Log in to Reply]  [No Email]
STEVE CAN

08-02-2004 05:55:00




Report to Moderator
 Re: Carb bolts seized in manifold in reply to Jon C -Florida, 08-02-2004 04:34:27  
Jon , What do you think about heating that manifold? It looks a little differant than the older tractors I have been working on!



[Log in to Reply]  [No Email]
Jon C -Florida

08-02-2004 07:42:09




Report to Moderator
 Re: Carb bolts seized in manifold in reply to STEVE CAN, 08-02-2004 05:55:00  
I think the manifold will be o.k. but I"m not so sure about the carb flange. Actually, I"m surprised that you havent twisted off those cap screws yet, as they wont take much torque.

At this point, I would "go for it" with the heat, as if you snap them off, you will be doing it anyway. Maybe put a wet rag draped on the carb, to keep that flange somewhat cooler.



[Log in to Reply]  [No Email]
STEVE CAN

08-02-2004 08:28:09




Report to Moderator
 Re: Carb bolts seized in manifold in reply to Jon C -Florida, 08-02-2004 07:42:09  
Jon, Just thought you would like to know, I did the heat trick and they both came out (hard all the way) with no damage to anything. I guess I am too cautious sometimes. So now a carb job next.Clooney mentioned its not an easy one to do and may be a good idea to get a vidio on it. THANKS for your time and advice



[Log in to Reply]  [No Email]
Jon C -Florida

08-02-2004 08:39:35




Report to Moderator
 Re: Carb bolts seized in manifold in reply to STEVE CAN, 08-02-2004 08:28:09  
Steve -
GREAT, I'm glad it worked out!

On the carb rebuild, I have already been through that battle too. My advice: send it out and get it done by one of the carb rebuild places (Dennys,Burrys, Roberts etc.) (Dennys is very fast....and they are all good.)
By the time you get done buying nozzels, and parts, drilling out holes with number drills, buying the vidio, trying it on the tractor a half dozen times (because you don't have a bench tester for it), you will probably wind up sending it out anyway.

Let me tell you, it is such a pleasure to just bolt the darn thing on and have the tractor run right. You will forget about the money when that two banger is popping along.

[Log in to Reply]  [No Email]
STEVE CAN

08-02-2004 09:22:49




Report to Moderator
 Re: Carb bolts seized in manifold in reply to Jon C -Florida, 08-02-2004 08:39:35  
Jon, Sounds like a good idea, I think I will take your advice. Would it be asking too much for the phone numbers and locations of the places you recomended? Then I could get the closest one. Thanks again



[Log in to Reply]  [No Email]
Jon C -Florida

08-02-2004 10:10:28




Report to Moderator
 Re: Carb bolts seized in manifold in reply to STEVE CAN, 08-02-2004 09:22:49  
Sure -here they are:

Dennys Carb: 1-937-368-2304 (Fletcher Ohio)

Burrys Carb: 1-260-623-2104 (Monroeville In)

Roberts Carb: 1-712-262-5311 (Spencer Il)

All are good..its just who can do it quickest.

All have good web sites...just type the name in a search engine and they will pop up.

Finally, make sure you have the corrrect carb for your tractor. I had a 720 that had an all fuel carb on it...but was supposed to be a gas only carb. No wonder it ran rough!

[Log in to Reply]  [No Email]
Jon C - Florida

08-02-2004 10:03:00




Report to Moderator
 Re: Carb bolts seized in manifold in reply to STEVE CAN, 08-02-2004 09:22:49  
Sure...here they are.

Denny's Carb: 1-937-368-2304 (Fletcher Ohio)

Burrys Carb: 1-260-623-2104 (Monroeville In.)

Roberts Carb: 1-712-262-5311 (Spencer Ill)

All have web sites...just type in each name in a search engine and it will pop up.

All are good...just a matter of how long you want to wait. By the way, I am assuming you have the correct carg for that tractor...some are all fuel and some are gas only. I had a 720 one time that came with the wrong carb...no wonder it ran lousy. You can double check on the web sites, or ask them when you call.

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy