Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

420 Slant Steer Value

Welcome Guest, Log in or Register
Author 
J C (Middle TN

07-26-2004 09:38:39




Report to Moderator

Is a 420-S with the slant steering wheel more valuable than one with the straight steering wheel ? If so can anyone give me a ballpark figure for one that is complete but has not run in two years, was running fine when parked. Has tach, front end weight & rear wheel weights. The sheet metal is in good condition. It runs on gas. Thanks in advance.




[Log in to Reply]   [No Email]
mike

07-26-2004 13:04:17




Report to Moderator
 Re: 420 Slant Steer Value in reply to J C (Middle TN), 07-26-2004 09:38:39  
Ther were only 1100 slant steers built.



[Log in to Reply]  [No Email]
buickanddeere

07-26-2004 11:36:11




Report to Moderator
 Re: 420 Slant Steer Value in reply to J C (Middle TN), 07-26-2004 09:38:39  
Float ride seat, 1000 rpm reto fit, spin out rims, remote hydraulic outlet, dual rockshaft, power steering, real Deere wheel weights, intact ring and pinion, live pto, 5 speed trans, long or short axles, fenders large or small?



[Log in to Reply]  [No Email]
mike

07-26-2004 13:03:30




Report to Moderator
 Re: Re: 420 Slant Steer Value in reply to buickanddeere, 07-26-2004 11:36:11  
A float ride seat and 1000 pto were not available
for a 420S,all standards had short axles and small fenders.Any 420 S will bring $2500 to $3500,I've seen nice originals bring from $5000
to $7500.



[Log in to Reply]  [No Email]
buickanddeere

07-26-2004 13:42:15




Report to Moderator
 Re: Re: Re: 420 Slant Steer Value in reply to mike, 07-26-2004 13:03:30  
1000rpm was a dealer instaled kit in 420/430 with internal parts, not an external gear box. Mighty rare $$$. Has to be a few out there. No float ride seats on a standard?



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy