Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

620 Rod Knock

Welcome Guest, Log in or Register
Author 
Popper Dick

07-20-2004 15:42:43




Report to Moderator

Well friends,

I am 67 years old and I have been on two cylinder JD's since I was seven. I changed my oil and filters, (a regular thing with me) and right after that I developed a rod knock. I have excellent oil pressure, no leaks, no smoke anywhere including the crankcase breather tube. It starts great on first turn everytime and has great power. I have never been into an engine overhaul on two cylinders.

It knocks at idle but not under load. Once the load levels out it knocks some but not as bad as at idle. The long screw driver and thumb in the ear finds the knock most prevelant in the crank shaft area.

Is there any vendor that does an exchange of block, head, rods, pistons and bearings?

Any input is greatly appreciated.

Thanks guys and gals.

Dick

[Log in to Reply]   [No Email]
FRITZ

07-21-2004 10:18:56




Report to Moderator
 Re: 620 Rod Knock in reply to Popper Dick, 07-20-2004 15:42:43  
I WORKED ON 620 THAT I THOUGHT HAD A ROD OUT OF IT.ENDED UP A SCREW FROM THE CARB BUTTERFLY CAME LOOSE AND IMBEDDED ON THE TOP OF PISTON.GOOD LUCK.



[Log in to Reply]  [No Email]
Carl NY

07-20-2004 19:05:28




Report to Moderator
 Re: 620 Rod Knock in reply to Popper Dick, 07-20-2004 15:42:43  
Everyone has given you the basic logical steps to determine your knocking problem. Check the easy parts first. I,m responding because I have just gone thru the same situatuion myself on a 1958 620. What I thought was a rod or piston pin noise turned out to be a broken ring and damaged piston. Time for block rebore & oversize pistons . Good luck.



[Log in to Reply]  [No Email]
Popper Dick

07-21-2004 18:46:55




Report to Moderator
 Re: Re: 620 Rod Knock in reply to Carl NY, 07-20-2004 19:05:28  
Carl,

Thanks for the reply, My 620 is also a 1958 production run. If you had a broken ring, wouldn't you also have oil consumption and smoke out the exhaust? My tractor does not burn a drop of oil and has zero smoke from anywhere.

I hope that at worse case I just will need to do a crank and bearing job.

Thanks again.

Dick



[Log in to Reply]  [No Email]
Carl NY

07-22-2004 05:59:26




Report to Moderator
 Re: Re: Re: 620 Rod Knock in reply to Popper Dick, 07-21-2004 18:46:55  

This tractor didn,t burn oil or smoke either. A small section of the ring had broken and broke a chunk off the piston in the wrist pin area. These noises are difficult to pin point as the noise travels thru the block. As one person stated, I thought a small screw had dropped out of the carb and was on the top of the piston. Check the flywheel & drive disc. first because if they are loose it will sound lke a loose rod.

[Log in to Reply]  [No Email]
F-I-T

07-20-2004 16:58:52




Report to Moderator
 Re: 620 Rod Knock in reply to Popper Dick, 07-20-2004 15:42:43  
Popper:

You might well have a rod problem, but as the others said, if you have no reason to swap the block et al, You should tr to keep your own known good block etc. I bet you can figure out your way through a rod bearing repair, crank grind (only if necessary), and whatever else it might need.

Try this first for me. See if the flywheel is tight. While there is a lot of emphasis on diesel flywheels and tightness, we had a '48 "A" that knocked one day, and the local dealer told us to remove the flywheel, clean the splines on the crank and flywheel really well, and reinstall using new bolts and setting the endplay correctly.

That solved the problem, and in your case it could be a cheap repair. You wouldn't want to find that out after you tore it down for rods.

Frank

[Log in to Reply]  [No Email]
720Deere

07-20-2004 16:53:35




Report to Moderator
 Re: 620 Rod Knock in reply to Popper Dick, 07-20-2004 15:42:43  
Popper,

I would check the easy stuff before you open the proverbial can of worms. Check crankshaft endplay, the clutch driver & the flywheel. All of these can and will cause noise in the crank area.

It is not as common on a 620, but a loose flywheel will knock pretty good. The clutch driver will rap pretty good too.



[Log in to Reply]  [No Email]
Ron

07-20-2004 16:31:09




Report to Moderator
 Re: 620 Rod Knock in reply to Popper Dick, 07-20-2004 15:42:43  
You can change rod bearings without tearing anything else down except removing the hood and bonnet.. Sounds more like crankshaft endplay, to me..

Ron.



[Log in to Reply]  [No Email]
G-MAN

07-20-2004 15:49:37




Report to Moderator
 Re: 620 Rod Knock in reply to Popper Dick, 07-20-2004 15:42:43  
I think outfits like Abilene Machine will sell bored/rebuilt blocks on an exchange basis and probably the pistons, rings and pins to go with them, and you might also be able to find a rebuild cylinder head as well. However, you're still going to have just about the same amount of work to swap out those parts as you will to rebuild/machine your parts, and depending on labor and machine-shop rates in your area, it may be cheaper to rebuild your stuff than remove and replace your parts with items from aftermarket sources. If you still have good power and low blowby, you might not gain much by replacing all those items. I'd do some further diagnosis and determine exactly what the knock is and the difficulty of repairing it before going to a worst-case scenario.

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy