Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

630 won't start

Welcome Guest, Log in or Register
Author 
MIKE HANLEY

01-24-2004 20:04:33




Report to Moderator

Just got back the 630 after having elec ING put in. It's an IGNITOR made by PERTRONIX. Not only put in the ING kit, but also the PERTRONIX coil. On the PERTRONIX kits the magnet slips over the dist shaft on top of the plate. No need to pull the dist. Ran good for a couple of days and parked it. Then a couple of days later went to start it and nothing!!! Pulled the plugs and grounded them to the block and rolled the engine over. Got enought spark to weld with. Smelled gas but to make sure pulled the bottom bowl off the crab just to make sure it was froze with water. That's O.K. To me it acts like it's out of time. Ran out of daylight (the only light I have in my outdoor shop) Will check that tomarrow. Question: Has anyone had something happen to or could it be that something goes wrong with the magnet of the magnet slips to throw off the timing.

[Log in to Reply]   [No Email]
Mike M

01-25-2004 05:27:40




Report to Moderator
 Re: 630 won't start in reply to MIKE HANLEY, 01-24-2004 20:04:33  
Mike; I was just wondering if you were having problems before,that made you want to install an electronic ignition ?



[Log in to Reply]  [No Email]
MIKE HANLEY

01-25-2004 06:31:26




Report to Moderator
 Re: Re: 630 won't start in reply to Mike M, 01-25-2004 05:27:40  
Installed the elec ING as it seemed like I was putting in points and condensers 4, 5 times a year. Would be running good and then would start on one and then would start poping on the other and after a couple of minutes straighten out. Change points and it was good for a couple of months again.



[Log in to Reply]  [No Email]
Mike M

01-25-2004 07:24:10




Report to Moderator
 Re: Re: Re: 630 won't start in reply to MIKE HANLEY, 01-25-2004 06:31:26  
It may be that the original problem -whatever it is- is still there ? Do you have spark plug covers on it ? If so{ spark you can weld with} may jump to them. If you have them installed I would remove them during the trouble shooting process. If not on now one less thing to be it. During trouble shooting I like to keep an open mind and double check the simplest little things cause often it seems some simple little thing can cause lots of big headaches. I start with the basics like, takeing apart all the wire conections and cleaning them,looking for bad or loose ends and solder on new ones if needed,cleaning the grounds,double checking that the right wires are hooked to the right terminals by the book. Think little problem big headache ,hopefully you can get to the bottom of it.

[Log in to Reply]  [No Email]
Clooney

01-25-2004 04:54:17




Report to Moderator
 Re: 630 won't start in reply to MIKE HANLEY, 01-24-2004 20:04:33  
Mike, your statement..."Got enough spark to weld with" ...Tells us you are at least getting a spark..

~So that leaves either getting the spark at the correct time, a fuel problem, or a compression problem..

~First place to start is to pull the distributor cap & look for moisture & hairline carbon tracks [that could make an engine sound like it's cranking while out of time]..

~While in there give the distributor shaft a shake by hand to see if the bushings are loose [loose distributor bushings will play havoc with the reluctor air gap during cold cranking]..

~Lets start with a spark at the correct time.. Pull the L/H plug, then re-attach it to the plug wire & lay it on the engine block, then pull the little cover in the center of the flywheel cover so you can see the flywheel.. Now crank the engine [have someone do it] with your finger over the L/H plug hole & see if the L/H plug is sparking as the punch mark on the flywheel hub lines up with the stamped dash in the bottom center of the flywheel cover when you feel compression.. [you can also use a timing light on the L/H plug wire & point it at the flywheel cover while cranking,, it should show the light flashing as the flywheel hub dot lines up with the flywheel cover's lower stamped dash]...If your spark isn't happening at the correct time you have an issue with that electronic ignition system [probably something has moved or has changed it's position]..

~Next, remove the carb drain plug, then unscrew the knurled knob on the fuel strainer & hold the knob down & see if you have pencil sized stream of fuel flowing out [if you don't,, you have a fuel restriction].. Probably ice in the tank fitting or strainer..

~Next run a compression test [maybe the cylinder walls are washed clean of oil from a rich problem].. Or just add a few ounces of oil to each cylinder..

~Make sure you install a new set of spark plugs before doing anything [just because they spark while out of the engine doesn't mean they will spark while under a compression load]... Now that you have a high output coil run the plug gap at .040"-.045" [you need good well insulated plug wires to do that though]

~If the above doesn't show you anything re-install both spark plugs, then take an old [known good] spark plug & open the plug gap to 3/16", then install that in one plug wire at a time & lay on the engine block, now crank the engine & see if you have a spark jumping that 3/16" gap..[it's possible the ignition supply voltage drops low enough during cranking [under compression load] to drop that electronic ignition module below it's operating voltage low limit....

~You might want to try a battery charger on the batteries to increase the battery voltage during cranking to see if that helps..

~Here's the bottom line....If, you have a good fuel/air mixture [no water] ,, & you have a blue spark AT THE CORRECT TIME,, & you have good compression,, it will start.. All you have to do is find out what's missing...

[email protected]

[Log in to Reply]  [No Email]
MIKE HANLEY

01-25-2004 06:44:21




Report to Moderator
 Re: Re: 630 won't start in reply to Clooney , 01-25-2004 04:54:17  
Checked out everything you listed yesterday except the timeing. Will try that after about 4 more cups of coffee and about 6 of those cancer sticks. It's the weekend and I'll play with it today yet. It was installed by the JD dearler, so if I don't get it going today, tommarrow I'll call them. They also installed a new cap, rotor. dust cover. It still has the old spark plug wires. Lit from the company recommed there wires, but don't see where they require it.

[Log in to Reply]  [No Email]
MIKE HANLEY

01-25-2004 06:50:13




Report to Moderator
 Re: Re: Re: 630 won't start in reply to MIKE HANLEY, 01-25-2004 06:44:21  
What gets me is that it was running good and then I parked it for a couple of days and then it wouldn't start. If it was acting up before I shut it off when I parked it it would be a easer to pin point. but that is not the case.



[Log in to Reply]  [No Email]
Clooney

01-25-2004 07:40:55




Report to Moderator
 Re: Re: Re: Re: 630 won't start in reply to MIKE HANLEY, 01-25-2004 06:50:13  
Mike, I'm not sure what ign coil was used but most of those E.I. coils don't use or require a ballast resistor... Make sure if your new coil doesn't require a ballast resistor that the dealer that installed your unit removed or by-passed your factory ballast resistor.

~You really should install new plug wires.. You don't really need to use the ones sold by the I.E. manufacturer but you need to see if your system does require resistor wires [some of those high output coils need resistor wires as the coil is designed around that resistance]..

~With all that points replacement you needed make darn sure your distributor bushings are in good shape & you don't have a lot of distributor shaft play or wobble..

[email protected]

[Log in to Reply]  [No Email]
John T

01-25-2004 07:17:27




Report to Moderator
 Re: Re: Re: Re: 630 won't start in reply to MIKE HANLEY, 01-25-2004 06:50:13  
Mike, you done broke the darn thing lol. Somewhere in all this mess you mentioned plug wires and the companys suggestions. The reason better ones with higher voltage insulation may be required with that new switch and coil is that (especially with a wider plug gap) youre runing at higher operatign voltages and need the better wires to avoid arcing at places other then the plug. Also, on modern automotive ignitions, many use some resistance either in the plugs (resistor plugs) and the wires or even both.

I cant explain why it worked one day but not the next, but I would still go ahead and check the base timing as we suggested below,,,,,make sure the unit is well attached and grounded to the base plate in the distributor,,,,,make sure the magnet ring on the distributor shaft hasnt moved,,,,, ,,,check for clean fresh fuel in the carb,,,,, ,maybe remove the air cleaner bowl to be sure of no water,,,,, ,check compression or even try squiritgn a lil oil into the cylinders which might increase compression,,,,, ,,

Give it 2 aspirins and call me at the office on Monday.

Best wishes n God Bless

John T

[Log in to Reply]  [No Email]
John T

01-25-2004 07:12:25




Report to Moderator
 Re: Re: Re: Re: 630 won't start in reply to MIKE HANLEY, 01-25-2004 06:50:13  
Mike, you done broke the darn thing lol. Somewhere in all this mess you mentioned plug wires and the companys suggestions. The reason better ones with higher voltage insulation may be required with that new switch and coil is that (especially with a wider plug gap) youre runing at higher operatign voltages and need the better wires to avoid arcing at places other then the plug. Also, on modern automotive ignitions, many use some resistance either in the plugs (resistor plugs) and the wires or even both.

I cant explain why it worked one day but not the next, but I would still go ahead and check the base timing as we suggested below,,,,,make sure the unit is well attached and grounded to the base plate in the distributor,,,,,make sure the magnet ring on the distributor shaft hasnt moved,,,,, ,,,check for clean fresh fuel in the carb,,,,, ,maybe remove the air cleaner bowl to be sure of no water,,,,, ,check compression or even try squiritgn a lil oil into the cylinders which might increase compression,,,,, ,,

Give it 2 aspirins and call me at the office on Monday.

Best wishes n God Bless

John T

[Log in to Reply]  [No Email]
Ron

01-24-2004 22:27:26




Report to Moderator
 Re: 630 won't start in reply to MIKE HANLEY, 01-24-2004 20:04:33  
Mike, I have never had this happen to me, but...

I have a friend who has a 620, and 530 that will refuse to start after sitting over winter, until he pulls the sparkplugs and puts some oil in the cylinders. JD says the rings loose their seal, and the oil gets them started just fine..only in the spring after setting.. Could this be the problem..??



[Log in to Reply]  [No Email]
Duane Larson

01-24-2004 21:36:09




Report to Moderator
 Re: 630 won't start in reply to MIKE HANLEY, 01-24-2004 20:04:33  
Mike,
I wonder if the electronic ignition unit may be temperature sensitive - is it cold there? Them 'lectrons maybe froze up?



[Log in to Reply]  [No Email]
John T

01-24-2004 20:41:53




Report to Moderator
 Re: 630 won't start in reply to MIKE HANLEY, 01-24-2004 20:04:33  
Geeee Mike, we hear how well those perform and Im always praising their advanatges over point and yours is broke. What did you do???

As far as their timing in general, the ring you placed over the distributor shaft has lil magnets which take the place of the high cam lobes function, and a pickup coil on the base plate replaces the points, and they fire when the magnet (used to be high cam) passes by the pickup coil (points). The location of the magnets on the shaft and the pickup coils location on the base determines timing.

I doubt if the pickup coil is moved off its base plate location, so has the ring you mounted on the shaft come loose or moved???? If either has moved, the timing will have changed.

You might check the mounting of the unit on the plate for a good ground and the wire connections on the coil while in there.

For timing to have changed, the magnets orrrrr pickup coil orrrrr rrrr distributors rotation location would have to change. HOWEVER, a bad ground or loose connection or even a bad unit can do funny things. You say she sparks well, any idea on the base timing if the spark is somewhere near the pistons TDC??? Maybe a timing light and/or the flywheels TDC marks to check the base timing for sure.

Be sure the gas is clean and fresh and the plugs good, but it sounds like the spark is fine and those ignitions can fire about any plug lol. The high voltage coils are more prone to arc at locations other than the plugs unless the wires and terminals are all in top shape. Did the units (coil or ignition) directions call for any special plug wires???

A bad unit or ground can cause fire at inappropriate timing, just check the magnets and connections and internal ground first and see what happens, then hook up a timign light and see just where shes firing. Check the plug wires also, maybe they are leaking???

Good luck, let us know, God Bless

John T

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy