Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

Front end loose on 2-wheel tricycle

Welcome Guest, Log in or Register
Author 
tom

09-15-2003 16:09:49




Report to Moderator

Gentlemen,

Have done the following to the tractor:

-Fixed the steering shaft/wheel, very tight & secure.

-Have adjusted the steering gear screw to take the play out of how she turns...also repacked the steering gear housing with fresh grease.

-Have replaced and repacked the bearings and seals for both tires...

However, the lower spindle/wheels still shake badly when driving...so I looked in the MT parts manual and sourced what "I think" [that could be bad], needs to be replaced. Below is a list of parts & JD part numbers. If anyone can help me to delete or add parts, or determine what I need by taking the front-end a part, it would be greatly appreciated. Right now the list is about $170...ouch!

1 M840T Seal, lower spindle
1 T12727T Bushing [sub for AM942T ]
1 M431T Seal, upper spindle
1 JD8820T Bearing, needle [sub for AM623T]
1 JD8404T Bearing, thrust
1 M4377T Washer, thrust bearing [sub for M842T]

Thank you in advance,
tom

[Log in to Reply]   [No Email]
Tom [thanks Chooch, Cloon

09-16-2003 16:17:37




Report to Moderator
 Re: Front end loose on 2-wheel tricycle in reply to tom, 09-15-2003 16:09:49  
Gentlemen,

I really appreciate your help and assistance... hope I can someday learn enough to return all the favors to you and the rest of the "YT Team".

I will perform the tests, then get the parts I need and give you all an update.

Regards,
tom



[Log in to Reply]  [No Email]
chooch

09-16-2003 09:42:17




Report to Moderator
 Re: Front end loose on 2-wheel tricycle in reply to tom, 09-15-2003 16:09:49  
Tom,
I think Wayne and Clooney have already mentioned the most likely candidates. I would suggest the following: (1) Remove the front wheels and lower spindle by removing the 4 bolts which attach it to the bottom of the front end support. (2)With the steering gear box off, it only takes three bolts to remove the steering gear support. (3) Remove the roll pin in the coupler and the upper spindle can be removed by sliding it out the bottom of the front end support(be careful that it doesn't fall out the bottom when the pin is removed). (4) At this point, you can inspect each of the splines on the upper spindle, coupler and the steering shaft. If none of the splines appear worn, then it might be the bearings. When I rebuilt the front end of my MT, I think Ma Deere told me that either the thrust bearing or the needle bearing one was no longer available. Fortunately, they both appeared in good shape and therefore I only replaced the lower bushing and seal.

[Log in to Reply]  [No Email]
Clooney

09-15-2003 16:22:24




Report to Moderator
 Re: Front end loose on 2-wheel tricycle in reply to tom, 09-15-2003 16:09:49  
Tom, my guess would be your problem is with the M-844-T coupling between the upper & lower steering spindles. You might also have some spline wear on the spindles where they connect to that coupling...

[email protected]



[Log in to Reply]  [No Email]
tom

09-15-2003 18:56:11




Report to Moderator
 Re: Re: Front end loose on 2-wheel tricycle in reply to Clooney , 09-15-2003 16:22:24  
Clooney,

Are you saying in addition to what I have listed that the coupling is also a problem, or is perhaps the sole problem? Is there a way to troubleshoot this to determine the actual problem before dissecting the front end?

Finally, is there any resolution to spline wear if it is not excessive?

thank you,
tom



[Log in to Reply]  [No Email]
Wayne in Tn.

09-16-2003 06:22:44




Report to Moderator
 Re: Re: Re: Front end loose on 2-wheel tricycle in reply to tom, 09-15-2003 18:56:11  
Tom, Clooney has you covered. One way to determine if you need the parts you have listed is to...With the tractor sitting still,in gear, and all the weight on the front wheels...grasp one of the tires with both hands at about 2 o'clock and 10 o'clock and try to roll the wheels front and backwards. If the parts you listed are worn, you will see the pedastile move back and forth. If not, probably the new coupler, that Clooney mentioned is all you need.
I recently had a tricycle 420 that you could do this test on and it would move back and forth seems like an inch or two (it was worn out) I replaced all the parts you listed, but not the coupler and WOW! What a difference, the front end was tight as new, and you could actually tell the difference just driving it around the yard. It cost me about $125 for the parts to rebuild the pedastile on a 420 or 430 tricycle.

[Log in to Reply]  [No Email]
Clooney

09-16-2003 03:35:21




Report to Moderator
 Re: Re: Re: Front end loose on 2-wheel tricycle in reply to tom, 09-15-2003 18:56:11  
Tom, you ask...
~"Are you saying in addition to what I have listed that the coupling is also a problem".....Tom, I said it COULD [my best guess] be the problem. Actually there is a good chance of it though.
~"Is there a way to troubleshoot this to determine the actual problem before dissecting the front end?".....Tom, yes, jack the front of the tractor up until there almost no weight on the front wheels, then look into the top of the steering gear while someone wiggles the front wheels within their play, if the wheels have a considerable amount of movement but the upper steering shaft doesn't move very much you probably have wear in something between the upper shaft & the wheels [that's usually that coupling & splines].
~� Finally, is there any resolution to spline wear if it is not excessive?��..Tom, that�s a good question, I have heard of people using everything from Loc-Tite gear & shaft repair to J.B. weld. While those products would probably remove the play, the chance of ever getting it apart again would be slim. I have only worked on a few of those T�s for loose steering & all I did was install a new coupling & live with the little extra play. If your spline wear is excessive you will have to figure something out. Maybe Wayne will jump in here, he works on an awful lot on those M�s & 40�s�
[email protected]

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy