Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

John Deere Tractors Discussion Forum
:

4020 Propane won't start!

Welcome Guest, Log in or Register
Author 
Don Arburn

01-13-2004 11:20:14




Report to Moderator

Turns over. New plugs, rotor, cap, wires and plugs and coil (6v). Hasn't run in four years or so, kept in shed. Got good spark and in the correct order. 12 volt pos. ground, new battery.

Ether will get a backfire and occassionally make it turn over real fast, but not actually running.

The propane is good.

The carb and regulator have been dismantled, adjusted and check out. It's getting fuel.

I have not checked compression, I have the wrong adapter for the guage. I'll get another today, if I can. I suspect a stuck valve -OR- a bad connection in the wiring harness.

Would a stuck valve cause this? Or would I need more than one stuck valve?

It has a 6 volt coil, which has me baffled a bit, there is supposed to be a resistance wire in the loom somewhere. Could this wire go bad (or be disconnected/corroded) and cause a no-start?

I'm stumped. I don't wanna tear into the head just yet. Help!

[Log in to Reply]   [No Email]
Tank

01-13-2004 17:41:43




Report to Moderator
 Re: 4020 Propane won't start! in reply to Don Arburn, 01-13-2004 11:20:14  
Sound like timing is too slow.Advance it a bit and see what happens.Propane likes alot of spark and advance because of it's higher flash point and higher octane rating-100+.



[Log in to Reply]  [No Email]
Don Arburn

01-13-2004 17:58:53




Report to Moderator
 Re: Re: 4020 Propane won't start! in reply to Tank, 01-13-2004 17:41:43  
Timing. O.k. Will check. Thanks!



[Log in to Reply]  [No Email]
zane

01-13-2004 16:50:16




Report to Moderator
 Re: 4020 Propane won't start! in reply to Don Arburn, 01-13-2004 11:20:14  
Try adjusting the ignition timing. I would start by retarding it a bit (rotating the distributor with the rotation of the rotor).

My little LP experience is with fork lift trucks. I do know that LP fuel supply systems can be tricky. Are you SURE that fuel/air supply to the engine is OK? Have you tried spraying ether directly into the carb's air intake while cranking with choke and throttle open?

Before removing the head, remove the valve rocker cover and observe valve action during cranking.

[Log in to Reply]  [No Email]
Don Arburn

01-13-2004 18:03:23




Report to Moderator
 Re: Re: 4020 Propane won't start! in reply to zane, 01-13-2004 16:50:16  
Timing. Will do.

Starting fluid (ether). Yes. Occassional Backfire and once it made the engine spin, not actually run, but run fast.

The valve cover is off. I didn't notice anything unusual, but I ran out of time and didn't observe from the other side yet. Will do.
Thanks!



[Log in to Reply]  [No Email]
twopop

01-13-2004 16:47:20




Report to Moderator
 Re: 4020 Propane won't start! in reply to Don Arburn, 01-13-2004 11:20:14  
the fuel system requires vacuum to open the regulator.if you have a leaking intake valve(backfire) it will reduce vacuum and will not open the regulator.you have alreadly stated the first and most important proceedure,take a compression test and go from there



[Log in to Reply]  [No Email]
Don Arburn

01-13-2004 18:09:17




Report to Moderator
 Re: Re: 4020 Propane won't start! in reply to twopop, 01-13-2004 16:47:20  
Would there be another vacuum source? Like on the regulator itself? Arg! I wish it were a gasoline engine sometimes.

Thanks!



[Log in to Reply]  [No Email]
twopop

01-13-2004 19:27:26




Report to Moderator
 Re: Re: Re: 4020 Propane won't start! in reply to Don Arburn, 01-13-2004 18:09:17  
as I recall,on the 4020 there is no other vacuum source. since you had it spinning with ether,I would suspect that you are either,getting to much fuel or not enough.some systems I have worked on would flood the engine with fuel,and without enough air,would not run.if I remember right,there is also a fuel solenoid and filter on the 4020.these shold be checked for operation.



[Log in to Reply]  [No Email]
Don Arburn

01-15-2004 09:23:51




Report to Moderator
 Re: Re: Re: Re: 4020 Propane won't start! in reply to twopop, 01-13-2004 19:27:26  
O.K. I'm an idiot. I had the plugs wires 180 out. Perhaps my father in law did it, but I shoulda checked. Went to TDC and discovered the error.

So it starts. Now I need to set the idle and I have no tach. Any suggestions?

This weekend we will set the timing, flush the coolant, change the oil and oil bath and filters and check the hydraulics. Anything else I should check for?

Thanks Guys! I am glad I found this great resource!

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy