Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Implement Alley Discussion Forum

feed grinder

Welcome Guest, Log in or Register
Author 
ryanfisher

02-28-2007 17:45:09




Report to Moderator

i am looking at a JD 400 feed grinder for sale. it has all parts there, except the auger right after the feed is ground is all rusted out. the guy doesn't know what its worth, so how much will it cost to fix and how much should i offer? i am looking to buy one if anyone has one for sale cheap(about $200-600). would prefer item in NE or bordering state. thanks for help.




[Log in to Reply]   [No Email]
Tim(nj)

03-02-2007 11:26:24




Report to Moderator
 Re: feed grinder in reply to ryanfisher, 02-28-2007 17:45:09  
What he has is scrap iron. Deere does not have parts support for the grinder mixers anymore, so fixing it may be next to impossible depending on what else is wrong with it (and trust me, if there is rust-through in one place, it"s in other places too.) For $200 to $600, you are not going to get anything much better than scrap metal. The only thing I can say is older New Holland and Arts-Way (also sold by IH) grinder-mixers have fairly decent parts support. My Gehl has OK support right now, but in a few years probably going to get a lot harder to fix.

[Log in to Reply]  [No Email]
T.K. in PA

03-03-2007 16:09:10




Report to Moderator
 Re: feed grinder in reply to Tim(nj), 03-02-2007 11:26:24  
H&S bought the rights to the GEHL grindermixer.



[Log in to Reply]  [No Email]
Stan - Florida

03-02-2007 17:35:45




Report to Moderator
 Re: feed grinder in reply to Tim(nj), 03-02-2007 11:26:24  
Tim,

Good to see you on here! I was beginning to worry about you.

Stan
Melbourne, FL



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy