Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Attention Forum Users: On the 28th of December 2023 at 9:00am Central Time, we will be taking the forums down for maintenance while we prepare the new forums for your use. Please click here for more information.

Case Tractors Discussion Forum
:

I'd like your comments

Welcome Guest, Log in or Register
Author 
Glenn FitzGeral

11-07-2004 16:19:42




Report to Moderator

A little further down this page I responded to a question "How many plows will my 830 pull?" I may be feeling a little ornry tonight but I'm gettin' a little tired of this question. The number of plows I hear of guys pullin' with their 50-60 hp tractors rival many fishing stories I've heard. And if you really want to put your boots on, go over to the IH board. I don't think they even put their plows in the ground over there. Soil conditions vary SOOO much! You will never hear me asking "How many plows will my new tractor pull?" as everyone's soil conditions vary. Generally I take people's reports, divide 'em by two and that's about the number of plows I'd pull here. Reading the operator's manual will give you a ballpark answer. I always subtract about one plow from what the manuals say as well. What do you think? Glenn FitzGerald

[Log in to Reply]   [No Email]
Roger (Mi)

11-13-2004 05:09:32




Report to Moderator
 Re: plowing rules of thumb in reply to Glenn FitzGerald, 11-07-2004 16:19:42  
Glenn, you must be plowing concrete. I've seen some heavy clay but not as bad as your describition.

The rule of thumb is 15 horsepower per bottom. An 830 Case should pull a 4 bottom plow well in most soil conditions.

Besides soil conditions, the way the plow is setup makes a difference in pulling difficulty. Just follow the 1"x 1" rule. The colter should be 1" above the plow point and 1" outside of the plow shank. In that way, the plow only needs to flip the soil instead of having to tear through it. That setting decreases the amount of power needed to pull the plow.

[Log in to Reply]  [No Email]
dbb62

11-09-2004 14:06:52




Report to Moderator
 Re: I'd like your comments in reply to Glenn FitzGerald, 11-07-2004 16:19:42  
Moldboard plowing is an art, and those of us who have gone over several thousand acres know that most of what has been said is right. It's all about soil conditions, soil conditions, and soil conditions. We plowed 2500 acres per year with 2 5/16 plows behind 2 (we are a non-denominational tractor family) John Deere 4020's - about 85-90 hp - in Northern Oklahoma. But, when things got hard it was in 2nd gear (out of eight). Loose soil with plenty of moisture it was in 3rd, but never in 4th, and my dad tought me you are wasting your time if you plow any shallower than 8 inches. When we upgraded to IH 5088's - about 130 hp - we had to buy new 6/18 plows cause we pulled the old ones to pieces.

Course if u really wanna see something I will try to arrange an opportunity for you to watch me pull the case 2/14 plow behind my 48 Case S. Now that's adventure plowin'. Gotta be careful when the land get's narrow cause you can get high centered if both rear wheels drop in the furrow at once!

I have seen moldboard plowing come and go out of vogue a couple of times, but every 10 years or so around us it comes back because without it the farmers can't control the cheat and weeds without using a bunch of costly chemicals.

[Log in to Reply]  [No Email]
C. Amick

11-08-2004 13:28:47




Report to Moderator
 Re: I'd like your comments in reply to Glenn FitzGerald, 11-07-2004 16:19:42  
Subtracting one plow from what the tractor owner's manual says is probably a good idea. Soils can definitely make a difference and so can the type of plows. We used to have a set of 3-point hitch Case plows that seemed hard to pull. We have a set of Case trail plows that are easy to pull. But pulling them is one thing and actually doing a good job plowing is another. Some Ford and Furgueson plows are easy to pull, but won't turn the sod all the way over. Case and IH plows seem to do a good job turning the sod over.

[Log in to Reply]  [No Email]
R Wyler

11-07-2004 18:36:19




Report to Moderator
 Re: I'd like your comments in reply to Glenn FitzGerald, 11-07-2004 16:19:42  
Yes that question cannot be given an accurrate answer due to what you stated above. 3-16s are a good pull for a 930 in my area though I could pull 4 with them also. There are way to many factors involved for a question like that to be answered accurately for any specific conditions I man would have to go talk to another from the same area and with the same exact tractor to get a good idea of what how many bottoms a tractor will pull. R Wyler

[Log in to Reply]  [No Email]
John Saeli

11-08-2004 04:47:24




Report to Moderator
 Re: I'd like your comments in reply to R Wyler, 11-07-2004 18:36:19  
Hey R.Wyler: 3-16's for a 930?? We got tight clay here, but my DC will pull 3-16's in 2nd, no problem. 870 plays with 4-16's. These are easy draft CASE plows, of course.



[Log in to Reply]  [No Email]
Glenn F.

11-09-2004 20:20:48




Report to Moderator
 Re: I'd like your comments in reply to John Saeli, 11-08-2004 04:47:24  
We were plowin' today. Mounted Case 3x14's behind the 930...3rd gear! Glenn F.



[Log in to Reply]  [No Email]
John Saeli

11-10-2004 03:39:31




Report to Moderator
 Re: I'd like your comments in reply to Glenn F., 11-09-2004 20:20:48  
Hey Glenn: Something is wrong!!!! We pull 5-16's in 3rd here. Our clay is heavier than yours.



[Log in to Reply]  [No Email]
Glenn F.

11-10-2004 05:03:32




Report to Moderator
 Re: I'd like your comments in reply to John Saeli, 11-10-2004 03:39:31  
We've come to see it as normal. We used to pull 4x18's with the 1270. 20.8x38 tires full of fluid, difflerential locked, in 1-2, 1-1. It was too much. We now pull 4x16's. Dad was pullin them yesterday while my brother was pullin the 3x14's. Such matches are the standard around here. Good, productive land. Good for corn or alfalfa. We can stand a good drought. Maybe I can post some pictures. Glenn F.

[Log in to Reply]  [No Email]
Glenn F.

11-10-2004 10:43:49




Report to Moderator
 Re: I'd like your comments in reply to Glenn F., 11-10-2004 05:03:32  
None of the neighbors are doin' any different with any color tractor or plow.



[Log in to Reply]  [No Email]
John Saeli

11-07-2004 19:33:50




Report to Moderator
 Re: I'd like your comments in reply to R Wyler, 11-07-2004 18:36:19  
Hey R.Wyler: 3-16's for a 930?? We got tight clay here, but my DC will pull 3-16's in 2nd, no problem. 870 plays with 4-16's. These are easy draft CASE plows, of course.



[Log in to Reply]  [No Email]
R Wyler

11-07-2004 19:39:02




Report to Moderator
 Re: I'd like your comments in reply to John Saeli, 11-07-2004 19:33:50  
Yes I use Case plows also I use only the best. GRIN. I can pull 4-16s I know though there are some very tough places where the front end gets light. R Wyler



[Log in to Reply]  [No Email]
Jim B

11-07-2004 18:05:42




Report to Moderator
 Re: I'd like your comments in reply to Glenn FitzGerald, 11-07-2004 16:19:42  
Guess I should've posted this reply here, not at the earlier original question! Here's a different slant for an answer/comment to the question... I have a 830 Gas COM and a 800 Diesel COM here in Southeast Michigan. Soil is highly variable, yellow sand to heavy clay. Have a set of Semi-Mount Case 16" and a set of Oliver 16" Trailer type. The 800 Diesel will out-pull the 830 Gasser with either plow set. The Oliver's pulls faster and deeper with either Tractor compared to the Case plows. I certainly prefer the 800 Diesel with the Olivers. Also less fuel cost. But the COM is mandatory due the the soil variability. Never have been able to plow at 5MPH average. But lately the 2470 with 3-point chiesel plow is the preferred choice. Moldboards are history! This statement should start another thread !!!

[Log in to Reply]  [No Email]
yo from ontario

11-07-2004 17:36:59




Report to Moderator
 Re: I'd like your comments in reply to Glenn FitzGerald, 11-07-2004 16:19:42  
I'd like to know why when I was a kid my dad could pull 3 x 12 with our 511B no draft control and no diff lock. Today that would mean that a 150 HP tractor should pull about 8 x 16 but we all know that never happens



[Log in to Reply]  [No Email]
DKase

11-07-2004 17:20:29




Report to Moderator
 Re: I'd like your comments in reply to Glenn FitzGerald, 11-07-2004 16:19:42  
I think you hit the nail square on the head!! I have an original brochure that brags the 830 as a 5-6 plow tractor. Anything over 4-16's would stop an 830 dead in our clay base soil. DK



[Log in to Reply]  [No Email]
SHeiserman

11-07-2004 17:16:33




Report to Moderator
 Re: I'd like your comments in reply to Glenn FitzGerald, 11-07-2004 16:19:42  
Hey Glenn. How much difference would the brand of plow make? I've read elsewhere IH and Oliver plows are best, and Case plows pull rather hard. To date, I've never pulled a Case plow. My first plow was an IH plow (5-18's) behind a 1370. The last being a JD (5-20's) behind a 4850. I do have a mounted 3-16 Case plow I was supposed to use this fall behind the 830, but haven't yet. I read the whole thread down there and thought it was interesting. Would like to know how the 830 will do.

[Log in to Reply]  [No Email]
Patrick (Mich.)

11-07-2004 21:58:43




Report to Moderator
 I forgot to mention... in reply to SHeiserman, 11-07-2004 17:16:33  
When I posted the thread asking how many bottoms my 830 would pull, that earlier this year I did some plowing at a steam threshers show. I hooked onto an old IH 3-16" trailer plow and made some passes in the field. In third gear, the engine acted as though nothing was even behind us, so I shifted into fourth for our next lap. We had no difficultly in pulling that either. My friend said it was too fast and might heat up the plow points too much, causing them to bend if we hit a stone. It was really throwing the dirt over! So from everything I have heard from you guys, it sounds like a four bottom set-up should work the best.

[Log in to Reply]  [No Email]
SHeiserman

11-08-2004 02:35:51




Report to Moderator
 Re: I forgot to mention... in reply to Patrick (Mich.), 11-07-2004 21:58:43  
Albert City? I had forgotten already, but I did see an 830pulling a trailer plow and it was having no trouble. There was also a 1200 (if I remember right) pulling 2 plows. That was the first and only time I have seen an 830 at play.



[Log in to Reply]  [No Email]
John H-WI

11-07-2004 17:37:30




Report to Moderator
 Re: I'd like your comments in reply to SHeiserman, 11-07-2004 17:16:33  
The brand of plows make a great difference. The 50's-60's Case plows pulled harder especially the 3-16's. I know Glen has a very hard soil to plow in but over in western Wisconsin the 830 will walk with 4-16's with out any difficulty if it ain't a Case plow. We pulled 4-14's with a 730 in fourth gear in the hills. This is a mixture of soils, black loam, clay, etc.. We used 5-16's behind a 970 which has about 30 more horses than the 830. The 830 would do 5 in sand but nothing else. It takes more than 67 hp to do it in most areas. The 4-14 plow we had behind our 730 pulled easier than the 3-16 that my Uncle had behind his 830. Gave the 830 all it wanted to pull that plow.

[Log in to Reply]  [No Email]
Tom (Ks)

11-07-2004 20:33:10




Report to Moderator
 Re: I'd like your comments in reply to John H-WI, 11-07-2004 17:37:30  
We pulled 5-16's with a 1030, 4-16 with a 930 in 4th gear. A 830 could pull 4-16's in third. We plowed about 10 inches deep back then. Keep in mind that a extra 2 to 4 inches deeper makes a world of difference. We are in northeast Kansas.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy